Table of Contents
Advertisement
Quick Links
ILS-606DBR
ILS-606DSR
ILS-625DCR
USER MANUAL
This manual includes instructions and overview on the following 3 CHAUVET products;
ILS-606DBR, ILS-606DSR and ILS-625DCR.
th
CHAUVET, 3000 N 29
Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
2005-03-09/22:45
Advertisement
Table of Contents
Related Manuals for Chauvet ILS-625DCR
Summary of Contents for Chauvet ILS-625DCR
- Page 1 ILS-606DBR ILS-606DSR ILS-625DCR USER MANUAL This manual includes instructions and overview on the following 3 CHAUVET products; ILS-606DBR, ILS-606DSR and ILS-625DCR. CHAUVET, 3000 N 29 Ct, Hollywood, FL 33020 U.S.A (800) 762-1084 – (954) 929-1115 FAX (954) 929-5560 www.chauvetlighting.com 2005-03-09/22:45...
-
Page 2: Table Of Contents
ABLE OF ONTENT TABLE OF CONTENT ... 2 BEFORE YOU BEGIN... 3 ... 3 HAT IS INCLUDED ... 3 NPACKING NSTRUCTIONS AC P ... 3 OWER ... 3 AFETY NSTRUCTIONS INTRODUCTION... 4 ... 4 EATURES DMX C ... 4 HANNEL UMMARY ILS? ... -
Page 3: Before You Begin
One of the following; ILS-606DBR - Trackscan 250DBR-ILS™ ILS-606DSR - Trackscan 250DSR-ILS™ ILS-625DCR - Colortrack 250DCR-ILS™ Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. -
Page 4: Introduction
CON controller, ILS fixtures are also addressed remotely by the controller further reducing the time to setup prior to a show. In short, CHAUVET’s ILS fixtures give the user the power and the speed to perform efficiently and effectively in the shortest possible time. -
Page 5: Product Overview
Product Overview Carrying handle Pan/Tilt Arm Hanging Bracket Removable Fixture Floor Stands! LED SEGMENT DISPLAY OVERVIEW LED I NDICATORS TATUS MASTER Slave Sound Flashing SEGMENT BUTTONS I/O PANEL OVERVIEW UTTONS Toggles programming MENU functions Steps backward through menu DOWN functions Steps forward through menu functions Confirms selected menu... -
Page 6: Setup
ETUP Lamp You will need to install a lamp prior to the initial operation of the fixture. A MSD250 high intensity discharge lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. -
Page 7: Mounting
Mounting H ANG I NG BRACKET & F IXT URE F LO O R STANDS Mount the hanging bracket on the fixture as illustrated on the right. The tension knob is unique in that it is self ratcheting, providing you tool-free tensioning of the bracket. -
Page 8: Operating Instructions
PERATING NSTRUCTIONS Menu Navigation To select any of the pre-set functions, press the MENU button until the desired function is shown on the display. Select the function by pressing the ENTER button and the display will blink. Use the DOWN and UP button to change the settings. -
Page 9: Operating Modes
The ILS system provides for the synchronization of all CHAUVET products whose model number is pre-fixed by the letters ILS. Master/Slave operation does not require any menu or setting selections. Simply connect each fixture in a daisy like fashion using qualified 3 pin DMX cables as described below. -
Page 10: Setting The Starting Address
You must make a selection within 8 seconds. Press the UP and DOWN buttons to toggle between the Slave Shows available. Note! There are 4 shows available in Model # ILS-625DCR and 2 shows in the rest. Press the ENTER button to activate selection. -
Page 11: User Configurations {Clnd}, {Ipan}, {Itlt}, {Irot}-606Dbr, {Idin
User Configurations {CLNd}, {IPan}, {ItLt}, {Irot}-606DBR, {IdIN} All of the fixtures have three user selectable run-time configurations that change the behavior of a certain function. The three functions are described below. CO L O R MO DE {CL ND} This mode allows you to select whether your controller will access the color palettes in solid colors only or solid and split colors. -
Page 12: Fixture Test And Service Functions {Fadj}, {Test}, {Fhrs}, {Rset
Press the MENU button to confirm or leave alone for 8 seconds. Fixture Test and Service Functions {FAdJ}, {teSt}, {FhrS}, {rSet} F O CUS ADJUST MENT {F ADJ } The focus adjustment tool activates a pre-set program that turns the lamp on and projects a gobo image so that you can manually adjust the focus. -
Page 13: Ca-8F Easy Controller (Optional)
CA-8 & CA-8F Easy Controller (Optional) The CA-8 Easy Controller is used only in master/slave mode. Connect the controller to the 1/4” microphone jack in the first unit. The table below describes the different preset shows the CA-8 Controller can command. CA-8 &... -
Page 14: Appendix
XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) -
Page 15: Dmx Channel Values (606Dsr & 606Dbr)
DMX Channel Values (606DSR & 606DBR) HANNEL 000 255 000 255 000 009 121 134 135 245 246 255 000 007 008 015 016 131 132 247 248 255 000 ... -
Page 16: Dmx Channel Values (625Dcr)
DMX Channel Values (625DCR) HANNEL 000 007 008 015 016 131 132 247 248 255 000 015 016 031 032 047 048 063 064 079 080 095 096 111 112 ... -
Page 17: Gobos
Gobos Open Dots Tunnel Broken Glass Open Dots Tunnel Broken Glass ILS-606 & ILS-625 User Manual 606DBR & 606DSR Swirl Cylinder Frost Breakup Triangle 625-DCR Frost Cylinder Frost Breakup 4 Dots 3200°K 6600°K 2005-03-09/22:45... -
Page 18: Maintenance
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the customer’s... -
Page 19: General Troubleshooting
Remote does not work Make sure connector is firmly connected to device Stand alone mode All CHAUVET lighting fixtures featuring stand-alone functions do not require additional settings, simply power the fixture and it will automatically enter into this mode Unit wobbles when... -
Page 20: Technical Specifications
Switch-selectable power settings ... 115V 60 Hz or 230V 50 Hz AC input ...3 prongs IEC 60320 C14 European version... 240V 50 Hz LAMPS CHAUVET US-HSD-250 ... 2000 hr, 6000K, 250W Philips MSD-250/2 ... 2000 hr, 6500K, 250W Philips MSD-200 ... 2000 hr, 5600K, 200W GOBOS Outside diameter ...26.8 mm...