Orbit ArizonaMist Instructions

orbit | ArizonA mist
®
PersonAl misting bottle instructions
Caution: Never dismantle any part of this product while it is pressurized!
Step 1: Filling the perSonal miSt bottle
Remove the cap by twisting in a counter clockwise
■
direction. This will separate the top from the Bottle Body.
Before the first use, rinse the inside of the bottle with warm
■
soapy water and towel dry .
Fill the bottle body with water, leaving approximately an inch
■
of space from the rim.
· NOTE: If water level is too high in the Bottle Body, it may
interfere with proper pressurization and prevent the
mist bottle from working at it's potential.
Step 2: Sealing the perSonal miSt bottle
Replace the cap onto the top of the Bottle Body, by
■
screwing the top on in a clockwise direction .
Ensure the cap is on tightly.
■
Double check the water level to ensure the bottle is not
■
over-full.
Step 3: preSSurizing the perSonal miSt bottle
Holding the Mist Bottle firmly in one hand, grasp the pump
■
handle with the other .
Pump the handle 12-15 times by sliding it up and down the
■
pump shaft. You will feel resistance as the pressure begins
to build within your Personal Mist Bottle.
It IS NOT necessary for your Personal Mist Bottle to be fully
■
pressurized to receive cooling output.
Step 4: how to miSt
Pull the Thumb Lever so that it moves away from the Mist
■
Nozzle .
The cooling mist will begin immediately for your enjoyment.
■
Caution: Never dismantle any part of this product while it is pressurized!
Orbit Irrigation Products, Inc.
®
North Salt Lake, UT 84054 USA
www.orbitonline.com | 1-800-488-6156
© 2010 Orbit Irrigation Products, Inc.
®
All rights reserved. All trade names are registered
trademarks of respective manufacturers listed.
p 801 295 9820
f 801 951 5815
www.fluid-studio.net
1065 South 500 West
Bountiful, Utah 84010
5
dimensions:
proof no:
flat: w: 8.5" h: 11"
date:
03.30.10
finished: w 8.5" d: 0" h 11"
des: spck:
MZ MZ
colors
job no:
N/A
client:
Orbit
sku:
20020
upc:
N/A
additional instructions:
· LB535940
file name:
20020-24 rA.indd
·
software:
InDesign CS3
8 oz. And 16 oz.
®
depreSSurization inStructionS
Depressurization of your Personal Mist Bottle is A MUST
before refilling or removig the cap FOR ANY REASON.
Hold your Personal Mist Bottle upside down so the Mist
■
Nozzle points toward the ground.
Pull the Thumb Lever away from the Mist Nozzle to begin
■
the depressurization .
There will be mist coming from the nozzle for the first few
■
seconds.
Continue holding your Personal Mist Bottle upside down
■
until you no longer hear air escaping from the nozzle.
cleaning and care
Rinse your Personal Mist Bottle with warm, soapy water
■
before use.
To clean your Personal Mist Bottle, always hand wash with
■
warm, soapy water and let air dry.
DO NOT PUT YOUR PERSONAL MIST BOTTLE IN THE
■
DISHWASHER.
DO NOT FREEZE WATER INSIDE OF YOUR PERSONAL MIST
■
BOTTLE.
Depressurize and empty any remaining water from your
■
Personal Mist Bottle after every use.
Allow your Personal Mist Bottle to air dry, upside down,
■
after every use.
Should the Mist Nozzle become clogged with calcium and
■
mineral buildup, DO NOT stick any sharp objects into the
orifice of the Mist Nozzle. Ensure your Personal Mist Bottle
is depressurized, unscrew the Mist Nozzle and soak, in a
glass dish, in vinegar or Orbit
overnight. Rinse well and screw back into your Personal
Mist Bottle.
color color
Registration non printing non printing
PMS
PMS
BLACK ???? ????
|Arizona Mist Nozzle Cleaner
® ®
PN 20020-24 rA
Printers are responsible for
meeting print production
requirements. Any changes
must be approved by the
client and Fluid Studio.
printed piece must meet
designated specifications
on this form.
PMS
????
© 2007 Fluid Studio. This
work is the property of Fluid
Studio, and cannot be used,
reproduced or distributed
in any way without their
express permission.