Network Setup - Emerson Liebert.PEX+ Series User Manual

44 Chapter 5 iCOM Controller

5.7.8 NETWORK SETUP

The NETWORK SETUP menu is used to set the parameters when the system is in a network subject to the monitoring
of a host. See Table 5-28 for parameter descriptions.
Parameters
S802 #UNITS
S803 TEAMWORK
S824 MON ADD
S825 MON T.O.
S825 MON H.S.
S830 UPGRSTAT
S830 UPGRADE
S831 CS CTRL
S831 CS STAT
S832 NW CTRL
S832 NW STAT
S835 MON PROT
S836 IP #1
S836 IP #2
S836 IP #3
S836 IP #4
S837 NM #1
S837 NM #2
S837 NM #3
S837 NM #4
S838 GW #1
S838 GW #2
S838 GW #3
S838 GW #4
S840 U2U PROT
S841 U2U ADD
S842 U2U GRP
S843 BL CTRL
S843 BL STAT
S844 SR CTRL
S844 SR STAT
SW#
MAC
NAME
Table 5-28 Descriptions of NETWORK SETUP parameters
Default Setting range
1 1 ~ 32
No No, 1, 2
3 1 ~ 99
No No, 1, 2
3 1 ~ 99
None,S CS,
S NS,S SR,
- S GDR,
SBLV,SRAM,
Ready,Fail
No,Yes,
-
ULock
Save, Load,
No
No
Change Change, Valid
Save, Load,
No
No
Valid Change, Valid
No,Vlct3,HN,
Vlct4
IGM,n.a.,Vlct4
192
168
-
254
1
255
255
-
255
0
0
0
-
0
0
GBP -
3 -
1 -
No S + R, No
Valid Change, Valid
No C + R, No
Valid -
- -
- -
UNIT UNIT
Liebert. PEX+Series Precision Air Conditioner
Range: 1 ~ 32
Range: No, 1, 2
Monitoring address No. of the unit
Monitoring Timeout
Monitoring Handshake
Lock for Upgrade Status
Lock for Upgrade
Save the parameter set through MON ADD to the iCOM controller.
'No' means not saved
Indication of the saving state of the parameter set through MON
ADD. 'Change' means that the parameter is changed but not saved.
'Valid' means that the setting is valid and saved
Save the parameter set through U2U GRP to the iCOM controller.
'No' means not saved
Indication of the saving state of the parameter set through U2U
GRP. 'Change' means that the parameter is changed but not saved.
'Valid' means that the setting is valid and saved
Host monitoring protocol setting. Range: Vlcty (Velocity uses
intelligent card), HN (Hironet), IGM (ECA2), No
Set IP address
Set subnet mask
Set gateway address
-
Group address No. of this unit
-
Boot program variant load. Saving the change of S835 ~ S841 needs
the S + R command of this parameter. The system will reset after the
saving, and configure according to the new parameters
Indication of whether or not the parameters set through S835 ~ S841
are saved. 'Change' means that the parameter is changed but not
saved. 'Valid' means that the setting is valid and saved
Static RAM data reset control. If the change of S835 ~ S841 are not
saved, using the C + R command in this parameter can restore S835
~ S841 to their original settings, and the system will reset afterwards
STD
Version No. of the control software
MAC address of the network card of the iCOM controller
Name of the unit. By default: UNIT. You can change the name as
you need
User Manual
Description