Table of Contents
Advertisement
Direct Drive tapping unit with touch screen multiple control panel
setting a production lot:
The "counter preset" box allows the user to enter a number >0 of threads to be performed. Once the parameter has been
entered the operator can press EXIT and begin the threading process. When the last thread of the program has been
made the machine will stop and an alarm will be displayed on the touch screen panel.
By pressing the alarm sign, the operator will get the message "A16: end of production lot".
Press RESET to get the machine to work again. The tapping unit is now ready for another production lot.
If "counter preset"=0, the tapping unit will work normally with no quantity limit.
The "RESET"keys next to the "actual count" and "total count" boxes are used for clearing count data and get ready for new
ones.
E) OIL
Setting a production lot
This function allows to turn ON/OFF the lubrication system and to control it by entering the lubrication time.
The "counter preset" box allows the user to enter a number >0 of threads to be performed. Once the parameter has been
— Manual lubrification : Enter "0" in the lubrication time box and keep pressing "ON" as long as the lubrication is needed.
entered the operator can press EXIT and begin the threading process. When the last thread of the program has been made
— Automatic lubrication: Enter a time parameter in "time oil". Press ON. The lubrication will last the entered time at every
the machine will stop and an alarm will be displayed on the touch screen panel. By pressing the alarm sign, the operator will
single cycle.
get the message "A16: end of production lot". Press RESET to get the machine to work again. The tapping unit is now
ready for another production lot.
Remember that the tap lubrication is one of the most important conditions to obtain a good performance in threading
: Enter "0" in the lubrication time box and keep pressing "ON" as long as the lubrication is needed.
If "counter preset"=0, the tapping unit will work normally with no quantity limit.
process and a long lasting tap. Special oil for threading is highly recommended.
: Enter a time parameter in "time oil". Press ON. The lubrication will last the entered time at every
The "RESET" keys next to the "actual count" and " total count" boxes are used for clearing count data and get ready for new
For connecting the lubrication system, see instructions on pages 13-23-33-43 of the wiring diagram attached to this
ones.
manual.
E)
OIL
This function allows to turn ON/OFF the lubrication system and to control it by entering the lubrication time.
F) PrOgrAm
Manual lubrification
This function allows storage and backup of threading settings. The page displays the following information:
Automatic lubrication
single cycle.
Remember that the tap lubrication is one of the most important conditions to obtain a good performance in threading process
and a long lasting tap. Special oil for threading is highly recommended
name of last loaded program
For connecting the lubrication system, see instructions on pages 13-23-33-43 of the wiring diagram attached to this manual
F)
PROGRAM
This function allows storage and backup of threading settings
key for loading a program
The page displays the following information:
field for naming a program
name of last loaded program
:
key for loading a program
saving a new setting:
field for naming a program
1.
Carry out set up (paragraph "SET UP" - page 5);
2.
From main menu, press SERVICE and then PROGRAM;
Saving a new setting
3.
1- carry out set up (paragraph "SET UP" - page 5)
Tap Program Select box and select the program where the new settings will be saved;
2- from main menu, press SERVICE and then PROGRAM
4.
Enter the name of the new program in the lower box;
3- tap Program Select box and select the program where the new settings will be saved
5.
Press SAVE : the new program will be saved and loaded;
4- enter the name of the new program in the lower box.
6.
Make sure that previous name in the "in work" field has changed into the new name. Press EXIT.
SERVICE
5- press SAVE : the new program will be saved and loaded
6-make sure that previous name in the "in work" field has changed into the new name. Press EXIT
PROGRAM9
M8X10
PROGRAM
PROGRAM0
(page 5)
PROGRAM1
1
2
Loading a program:
SERVICE
M8X10
PROGRAM
(page 5)
1
2
In case the loaded program has a different rotation (left/right threading) than the previous one, the panel must
Loading a program:
1- from main screen, select SERVICE and then PROGRAM.
2- tap "Program Select"
3- scroll and select the program from the menu
PROGRAM5
SERVICE
4- press LOAD.
PROGRAM5
5- make sure that the program has been loaded: the name should appear in green characters on top. Press EXIT.
PROGRAM
ATTENTION:
In case the loaded program has a different rotation (left/right threading) than the previous one, the panel must
PROGRAM5
be turned off and on before starting the threading process otherwise it won't change the direction
1
.
: Enter "0" in the lubrication time box and keep pressing "ON" as long as the lubrication is needed.
: Enter a time parameter in "time oil". Press ON. The lubrication will last the entered time at every
M8x10
M8x10
M8x10
M8x10
:
M5x8
PROGRAM0
PROGRAM1
3
M5x8
PROGRAM9
PROGRAM0
PROGRAM1
PROGRAM1
3
PROGRAM5
PROGRAM5
program1
M3X6
program3
2
3
scroll menu with n. 10
available programs:
program1
M8x10
program3
key for saving and loading a program
M8x10
M8x10
view of the last loaded program
M5x8
M5x8
PROGRAM0
M8x...
M8x10
view of the last loaded program
4
M5x8
PROGRAM0
M8x...
4
PROGRAM5
M3x6
PROGRAM5
4
scroll menu with n. 10
available programs:
program1
M8x10
program3
key for saving and loading a program
M8x10
M8x10
M8x10
5
6
M5x8
PROGRAM0
M8x10
5
M3x6
M3x6
M3x6
5
M8x10
M8x10
M8x10
6
11
Advertisement
Table of Contents
