Figure 8. Mounting Bracket Assembly; Table 3. Pole Mount Hardware - ADTRAN T200 H2TU-R Installation And Maintenance Manual
High capacity cabinet
Hide thumbs
Also See for T200 H2TU-R:
- Installation and maintenance manual (24 pages) ,
- Quick start manual (2 pages) ,
- Manual (2 pages)
Table of Contents
Advertisement
Table 3. Pole Mount Hardware
P
o
e l
m
o
u
t n
k
D
e
s
c
i r
t p
o i
*
L
t f i
n i
g
e d
a t
l i
*
*
P
o
e l
m
o
u
t n
b
a r
k c
t e
l (
t f i
P
o
e l
m
o
u
t n
n i
g
u s
p
p
o
t r
b
3
8 /
-
1
6
x
" 1
B
o
s t l
3
8 /
l F
t a
w
a
h s
r e
3
8 /
S
p
t i l
w
a
h s
r e
3
8 /
S
e
l a
n i
g
w
a
h s
r e
*
F
s a
e t
e n
s r
s u
d e
o t
t a
a t
h c
r p
- e
n i
e s
t r
d e
n i
o t
t
e h
r i
d
s e
*
*
T
e h
p
o
e l
m
o
u
t n
n i
g
b
a r
e d
a t
l i
d
r u
n i
g
i
s n
a t
l l
t a
o i
. n
4. Attach lifting details. Screwed into each side of
the cabinet is a group of three bolts and washers.
Remove these for reuse.
NOTE
Observe that one of the lifting details is also
the mounting bracket. Ensure the mounting
bracket is attached to the side of the cabinet
designated to be against the pole.
5. Following the illustration in Figure 8, attach the
lifting details to each side of the cabinet using
the bolt and washer groups. Ensure the sealing
washers are placed between the cabinet and the
lifting details. Tighten bolts to 110-130 in-lbs.
WARNING
Exercise caution and observe all safety
measures when lifting the cabinet out of the
shipping package and during installation.
WARNING
Do not disconnect lifting cable until the cabinet
is fully secured and all mounting bracket and
support fasteners are tightened.
6. Using appropriately sized and tested hoisting
gear, attach a hoist cable between the lifting
details. Hoist the cabinet from the package and
lower the cabinet onto its side.
61150090L1-5A
t i
P
t
#
2
1
5
0
0
9
0
9 -
n
Q
u
a
n
i t
1
n i
g
e d
a t
) l i
1
a r
k c
t e
2
4
6
4
4
l
t f i
n i
g
e d
a t
s l i
a
e r
h s
p i
p
d e
g i
n
t a
d e
a c
i b
e n
l t
c o
t a
o i
n
. s
k c
t e
e s
v r
s e
s a
a
l
t f i
n i
g
Section 61150090L1-5A, Issue 1
y t
sealing washer
Figure 8. Mounting Bracket Assembly
7. Remove hardware securing the wooden boards
to the bottom of the cabinet.
Do not reuse shipping hardware. It is not
designed for cabinet mounting.
8. Identify which side of the cabinet will be
mounted to the pole and on that side attach
(finger tight) the slotted end of the two bottom
support brackets. Ensure the short end will point
down after the cabinet is upright and that the
sealing washers are against the bottom of the
cabinet. Refer to Figure 9. Ensure a flat washer
is on both sides of the support bracket.
9. After determining the appropriate upper
mounting height of the cabinet, drill a 5/8" hole
through the pole for the top pole mounting
bracket. The 1/2 inch diameter through-bolt, nut,
and washers are customer supplied. Install the
bolt through the pole and tighten to leave the
bolt head approximately 1 3/4 inches from the
pole to allow the upper pole mounting bracket to
slide over and down, catching the bolt head.
Refer to Figure 10.
10. Maneuver the cabinet so as to fit the through bolt
head through the slot key opening on the
mounting bracket. When the cabinet is hanging
Mounting Bracket shown,
Lifting Detail similar.
Bolt torque:
110-130 in-lbs
flat washer
bolt
split washer
CAUTION
7
Advertisement
Table of Contents
