ADTRAN HDSL4 Quick Start Manual

HDSL4 T200
LED STATUS
H4TU-R
DSL1/DSL2
CLEI: T1L5J61C_ _
DS1
1221424L1 ALM
DSL 1
ESF/SF
DSL 2
DS1
B8ZS/AMI
ALM
LBK/RLB
ESF/SF
(YEL) (GRN)
B8ZS/AMI
(YEL) (GRN)
LBK/RLB
NOTE: When used with an ADTRAN H4TU-C, the terminal screens via the H4TU-R will display
(YEL) (GRN)
information that is stored at the H4TU-C.
OPTIONS
Faceplate Buttons
LOC
LOC Initiates a bidirectional loopback of the H4TU-R toward the network and customer
REM Initiates a loopback at the H4TU-C toward the customer
LBK
REM
TX
TX
M
O
N
RX
RX
R
S
2
3
2
C A U T I O N C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
For a complete Installation and Maintenance Practice (P/N 61221426L1-5): (877) 457-5007, faxback Document 826. Please have your fax number ready.
HANDLING PRECAUTIONS REQUIRED.
HDSL4 T200 H4TU-R FOR LOCAL POWER
Green Normal operation; signal quality (SNR Margin) is optimum on
Loop 1/Loop 2 between the H4TU-C and the H4TU-R.
Red Severely impaired operation; signal quality (SNR Margin) is 0 dB on
Loop1/Loop 2 between the H4TU-C and the H4TU-R.
Green DS1 signal from the CPE is present at the H4TU-R.
Red DS1 signal from the CPE is absent at the H4TU-R.
Off No alarm condition detected.
Red Alarm condition detected either locally (H4TU-R) or locally and
remotely (H4TU-R and H4TU-C).
Yellow Remote (H4TU-C) alarm condition detected.
Off Indicates received DS1 signal is unframed.
Green Indicates received DS1 signal is SF framed.
Yellow Indicates received DS1 signal is ESF framed.
Green The unit is receiving AMI line code.
Yellow The unit is receiving B8ZS line code.
Off Unit is not in the armed or loopback state.
Yellow A local loopback is active on this specific unit.
Green A remote loopback is active on this specific unit.
POWER
This specific unit is intended for Local Power Only. If a Span Powered unit is needed, refer to
P/N 1221426L1.
DS1 MONITOR JACKS
TX DS1 signal from CPE toward Network
(nonintrusive)
RX DS1 signal from Network toward CPE
(nonintrusive)
COMPLIANCE
Warning: The DSX-1 interface is intended for
connection to intra-building wiring only.
Ensure chassis ground is properly connected.
This product is intended for installation in
restricted access locations only and in equipment
with a Type "B" or "E" enclosure.
This product meets all requirements of Bellcore
GR-1089-CORE (Class A2), ANSI T1.418-2002.
Code Input Output
Power Code (PC) C C
Telecommunication Code (TC) X X
Installation Code (IC) A –
This product is NRTL listed to the applicable UL
standards.
JOB
A
ID
61221424L1-22A
0208
CARD EDGE PIN ASSIGNMENTS
Chassis Ground
1
2
3
4
DS1 TX Tip
5
6
HDSL4 Tip (Loop 1)
7
8
9
10
Chassis Ground
11
12
HDSL4 Ring (Loop 1)
13
14
DS1 Tx Ring
15
16
-48 VDC Return
17
18
19
VCC
20
21
22
23
24
25
26
Chassis Ground
27
28
29
30
31
32
33
34
-48 VDC
35
36
37
38
39
40
HDSL4 Tip (Loop 2)
41
42
43
44
45
46
HDSL4 Ring (Loop2)
47
48
DS1 Rx Ring
49
50
51
52
53
54
DS1 Rx Tip
55