Table of Contents
Advertisement
6.1.
Recheck the operation of the control.
6.2.
Visually inspect the appliance. Clean off any
marks incurred during installation.
6.3.
Advise the customer how to operate the
appliance.
6.4.
Advise the user that the appliance can be lit with
a match if necessary by inserting it through the central
opening at the bottom of the radiant box.
6.5.
Advise that the dressguard can be removed to
replace the radiants.
6.6.
Advise that any cleaning must only be carried
out when the fire is off and cold.
• Always turn off the gas supply and make sure that the
appliance is cool before commencing any servicing.
• Always test for gas soundness and spillage after
servicing the appliance.
• It is recommended that, at least once a year, the
appliance is disconnected and the catchment space
behind the closure plate checked and cleared of any
debris. The closure plate must be resealed to the wall
after checking.
7.1.
TO REPLACE RADIANT(S)
7.1.1.
Remove the dress guard by pressing down the
two hooks at the top. Tilt the guard forward and lift out.
7.1.2.
Remove the old radiant(s) Fit the new radiant(s)
ensuring that they rest against the rear support bar and
that their bottom front edges are behind the retaining
tags near the front of the radiant box.
7.1.3.
Replace the dress guard.
Locate the bottom of the dress guard in the two holes in
the apron. Engage the two spring projections at the top
of the guard in the slots under the front canopy.
7.2.
TO GAIN ACCESS TO BURNER,
PILOT, TAP ETC.
7.2.1.
Remove the dress guard by pressing down the
two hooks at the top. Tilt the guard forward and lift out.
7.2.2
Remove the control knob.
7.2.3
Unscrew the two case securing screws (one
either side) located in the recesses near the bottom rear
of the outer casing sides.
7.2.4
Lift the outer casing assembly clear and place
safely to one side.
6. FINAL REVIEW
7. SERVICING & PARTS REPLACEMENT
6.7.
Mention that the radiants may become brown
with use, that this is quite normal and has no adverse
effect.
6.8
Recommend that the appliance should be
serviced and the chimney inspected by a competent
person (In the UK a CORGI registered person) at least
annually.
If the appliance is in premises in the United Kingdom occupied
by a tenant, point out that by law a landlord must have any gas
appliance, flue and pipework which is situated in a tenant's
premises checked for safety at least every 12 months.
6.9.
Hand these instructions and the user's
instructions to the customer.
7.3.
TO REPLACE THE PILOT UNIT
7.3.1.
To gain access see section 7.2.
7.3.2.
Disconnect the thermocouple connection at the
bottom of the gas tap.
7.3.3.
Disconnect the pilot pipe from the gas tap. It is
the upper connection at the right side of the tap.
7.3.4.
Remove the first screw securing the dust cage to
the pilot unit and burner. Carefully remove the dust cage
and place aside. Remove the second screw securing the
pilot unit to the burner.
7.3.5.
Disconnect the electrode lead from below the
pilot electrode.
7.3.6.
Carefully remove the pilot unit together with
the pilot pipe then disconnect the pipe from the pilot
unit.
7.3.7.
Replace in the reverse order.
Note: 1 The pilot unit must be replaced as a whole assembly.
Its individual components are not separately replaceable.
2. Once removed, ensure that the dust cage is cleaned
before refitting. Make sure that it locates squarely onto the pilot
unit without any gaps between the cage edges and the pilot unit.
7.4.
TO REMOVE THE BURNER, GAS
TAP & PILOT ASSEMBLY
7.4.1.
To gain access see section 7.2.
7.4.2.
Make sure that the gas tap is in the off position.
Disconnect the control spindle & adapter from the gas
tap by removing the split pin. Lift the adapter clear of the
gas tap spindle.
7.4.3.
Disconnect the inlet pipe from the gas tap. It is
the lower connection at the right side of the tap.
7.4.4.
Slacken the wing nut at the left side of the
burner. Remove the screw from the captive nut at the
11
Advertisement
Table of Contents
