Fcc, Acta And Ic Regulations - VTech IS8151-1S User Manual

FCC, ACTA and IC regulations

FCC Part 15
NOTE: This equipment has been tested and found to comply
with the requirements for a Class B digital device under Part 15
of the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications may not be
ensured when using this telephone.
To ensure safety of users, the FCC/ISEDC has established
criteria for the amount of radio frequency energy that can
be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested
and found to comply with the FCC/ISEDC criteria. The handset
may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user's
body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian
requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the back
or bottom of this equipment contains, among other things,
a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your telephone service provider
upon request.
The plug and jack used to connect this equipment to
premises wiring and the telephone network must comply with
applicable Part 68 rules and technical requirements adopted
by ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to
a compatible modular jack that is also compliant. An RJ11 jack
should normally be used for connecting to a single line. See
the installation instructions in the user's manual.
The Ringer Equivalence Number (REN) is used to determine
how many devices you may connect to your telephone line
and still have them ring when you are called. The REN for this
product is encoded as the 6th and 7th characters following the
US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0)
or less. For more information, please contact your telephone
service provider.
This equipment may not be used with Party Lines. If you have
specially wired alarm dialing equipment connected to your
telephone line, ensure the connection of this equipment does
not disable your alarm equipment. If you have questions about
what will disable alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged
from the modular jack until the problem has been corrected.
Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement
procedures, follow the instructions outlined under the Limited
warranty.
If this equipment is causing harm to the telephone network,
the telephone service provider may temporarily discontinue
your telephone service. The telephone service provider is
required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem and
the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper
functioning of this product. The telephone service provider is
required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it
is hearing aid compatible.
If this product has memory dialing locations, you may choose
to store emergency telephone numbers (e.g., police, fire,
medical) in these locations. If you do store or test emergency
numbers, please:
Remain on the line and briefly explain the reason for the call
before hanging up.
Perform such activities in off-peak hours, such as early morning
or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic
Development Canada's licence-exempt RSS(s). Operation is
subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Privacy of communications may not be ensured when using this
telephone.
The term ''IC:'' before the certification/registration number only
66