Table of Contents
Advertisement
Quick Links
Owner's Manual
Liberty ADA Desks
Crank-Adjustable
38792
38793
38932
38933
Crank-adjustable
IMPORTANT:
Before you begin, please make sure all parts and proper
quantities are included. Any parts damaged during
shipment must be reported within 15 days of receipt. To
report information regarding damages or if you have any
questions, please call 1-800-235-1262.
CAUTION:
Before using this product, read this manual and follow all
safety and operating instructions.
To purchase parts or accessories, please contact us at
www.spectrumfurniture.com
1-800-235-1262
Thank you for choosing Spectrum products!
Spectrum Industries, Inc.
Chippewa Falls, WI 54729, USA
44" CLASS
48" CLASS
44" Evolution
48" Evolution
Electric ECS-Adjustable
44" CLASS
38790
48" CLASS
38791
44" Evolution
38935
48" Evolution
38936
Electric ECS-adjustable
055311R5 Page 1 of 7
055311R5 Page 1 of 7
Advertisement
Table of Contents
Related Manuals for Spectrum Industries Liberty ADA 38792
Summary of Contents for Spectrum Industries Liberty ADA 38792
- Page 1 Before using this product, read this manual and follow all safety and operating instructions. To purchase parts or accessories, please contact us at www.spectrumfurniture.com 1-800-235-1262 Thank you for choosing Spectrum products! Spectrum Industries, Inc. Chippewa Falls, WI 54729, USA 055311R5 Page 1 of 7 055311R5 Page 1 of 7...
- Page 2 Safety ● Read this owners manual before operation ● For indoor use only. Do not install or store the unit where it will be exposed to weather. Keep unit dry. ● For added safety, plug the unit into a grounded three-prong receptacle controlled by a GFI (Ground Fault Interrupter) circuit breaker.
- Page 3 2. Attach Legs & Drive Assemblies to Worksurface A. Carefully flip the worksurface face-down onto a non-abrasive surface and orient the right leg as shown in Figure 2. B. Attach the right leg and right-hand hex drive bar assembly to the worksurface using 1/4-20 x 5/8" PHM screws. (Be sure the drive bar shaft is fully-inserted into the gear box before attaching.) C.
- Page 4 Electric ECS Desk Assembly / Setup: 1. Attach Legs to Worksurface A. Carefully flip the worksurface face-down onto a non-abrasive surface. Figure 1. B. Attach each leg to the worksurface using (8) 1/4-20 x 5/8" PHM screws. Control #8 x 3/4" PHSM (4 req'd) Right Leg Control...
- Page 5 3. Attach T-Supports, Cord Channel, & Chair Rail A. Attach the T-supports to the worksurface using (4) 1/4-20 x 1-3/4" PHM screws. Figure 3. B. Attach the cord channel to the T-supports using (4) 1/4-20 x 5/8" PHM screws. C. Attach the chair rail using (2) 1/4-20 x 2" FHM screws. (These screws will attach to the T-support ends.) 1/4-20 x 5/8"...
- Page 6 5. Control Panel Operation, Memory Presets, & Reset Procedure A. Plug in the power cord. Route cord so it is not a tripping hazard. B. To adjust the desk height, press the "Up" or "Down" arrow keys until the preferred height is achieved. Figure 5. C.
- Page 7 Warranty WE WILL MAKE IT RIGHT FOR YOU! We guarantee all Spectrum products to be free of all defects in materials and workmanship, for the original owner, for a period of ten years. Any item deemed defective by Spectrum or the original manufacturer, under normal use conditions, will be repaired or replaced at Spectrum’s discretion.
Need help?
Do you have a question about the Liberty ADA 38792 and is the answer not in the manual?
Questions and answers