Reversing - Zodiac EziSalt Installation Manual

EziSalt Saltwater Chlorinator | Installation Manual
MAIN MENU
-PROGRAMMING < -FILTER PUMP
-LOW MODE -SWC
-SLAVE MODE -AUX/LIGHTS
FILTRATION TIMER FILTRATION TIMER
-PUMP TIMER 1 <
-PUMP TIMER 2 -PUMP 1 ON
-PUMP 1 OFF 12:30
10. When a filtration program has been confirmed
the letter "P" is displayed on the top right of
the screen.
23:04 ON P
Manual activation of the device (pressing
takes priority over the timer. If no filter pump is
connected, the controller will only start chlorination.
If a filter pump has been connected the filter pump
will start along with chlorination. All programs will
still be valid and will resume normal operation the
next cycle.
7.3.4 Salt Water Chlorinator (SWC)
Programming
If a filtration program has been set, the chlorination
program will be identical to the filtration program(s)
by default. They can be changed, however the
chlorination program(s) cannot be activated outside
of the filtration Program(s) for safety reasons.
1. Press .
2. Use to select "Programming"
then press .
3. Use to select "SWC" then press
4. Use to select "SWC Timer 1" or "SWC
Timer 2" then press
5. Use to select the hour for the SWC on
time then press
6. Use to select the minutes for the SWC
on time then press
7. Use to select the hour for the SWC off
time then press
8. Use to select the minutes for the SWC
off time then press
9. Press to exit.
MAIN MENU
-PROGRAMMING < -SWC
-LOW MODE -AUX/LIGHTS
-SLAVE MODE -RESET TIMERS
SWC TIMER
-=FILTER PUMP
-SWC TIMER 1 < -SWC1 ON
-SWC TIMER 2 -SWC 1 OFF
The "T" symbol is displayed in the upper right hand
corner of the LCD display on the home screen if
the programming is valid.
PROGRAMMING
<
04:30 <
.
.
.
.
.
.
PROGRAMMING
<
SWC TIMER
04:30 <
12:30
The "P" symbol is displayed in the upper right-hand
corner of the LCD display on the home screen if a
valid filter pump and chlorinator program has been set.
23:04 ON
7.3.5 AUX/Lights Programming
1. Press
2. Use
then press
3. Use
)
4. Use
.
5. Use
time then press
6. Use
time then press
7. Use
time then press
8. Use
time then press
9. Press
MAIN MENU
-AUX/LIGHTS
-PROGRAMMING
-LOW MODE
-SLAVE MODE

-REVERSING

-HELP MENU
-LANGUAGE
AUX 2
-OFF
-ON
-SET TIMERS
7.4 Reversing
Adjusting your cell reversal times will result in voiding
of warranty. You must consult with Zodiac on 1300 763
021 or your local pool care professional before making
any adjustments.
The chlorinator uses a smart polarity reversal
system. Periodic polarity reversal will prevent
scaling of the cell plates. The time between each
reversal is factory set at 5 hours. This setting
is optimal for most water conditions. However,
Depending on the calcium hardness of the water,
you may need to adjust the reversal time. More
calcium in the water will require less time between
reversals. Water with less calcium can be given
more time between reversals. Shorter reversal
times will cause more wear of your cell plates. The
polarity reversal interval can be adjusted from 2 to
8 hours in 1-hour steps.
T 23:04 ON
.
to select "Programming"
.
to select "AUX/Lights" then press
to select "AUX 2 Timer" then press
to select the hour for the AUX on
.
to select the minutes for the AUX on
.
to select the hour for the AUX off
.
to select the minutes for the AUX off
.
to exit.
AUX/LIGHTS
<
-ASSIGN LIGHTS
-AUX 2
AUX TIMER
-AUX 2 ON 04:30
< -AUX 2 OFF 12:30
IMPORTANT
Page 15
P
.
<
<