Table of Contents
Advertisement
Page 14
7.2.2
White Light Operation
1.
Press
.
2.
Use
to select "Aux/Light" then press
3.
Use
to select "Aux 2/Light" then press
4.
Use
to select "On", "Off",
or "Set Timers", then press
5.
Press
to exit.
AUX 2
-OFF
<
-ON
-SET TIMERS
7.2.3
Color Light Operation
1.
Press
.
2.
Use
to select "Aux/Light" then press
3.
Use
to select "Aux 2/Light" then press
4.
Use
to select desired color, "Off",
"On" or "Define Color", then press
5.
If "Define Color" selected, use
desired color then press
6.
Press
to exit.
AUX 2 / LIGHT
-OFF
-ALPINE WHITE
-ON
-SKY BLUE
-DEFINE COLOR
<
-COBALT BLUE
-CARIBBEAN BLUE
-SPRING GREEN
-EMERALD GREEN
-EMERALD ROSE
-MAGENTA
-VIOLET
-SLOW SPLASH
-FAST SPLASH
-AMERICA
-FAT TUESDAY
-DISCO TECH
NOTE: Colour sequence is relevant for Zodiac colour
lights only. If other manufacturers lights are
installed the colour selection will vary
7.3
Programming/Timers
The controller has two internal operating timers.
The timers are used to define the length of time for
the filter pump to operate, and the length of time
for the Salt Water Chlorinator (SWC) to produce
chlorine. This offers the user the advantage of
running their variable speed pump longer at lower
flow rates, without having the chlorinator producing
the whole time.
In order to complete the timer program, it is
necessary to enter and validate both ON and
OFF times. If no timer is set, the filtration and / or
chlorination will run continuously
The filtration operating times must be sufficient to
correctly treat the water.
.
.
to select
.
COLOR LIGHT
<
Example - single speed pump:
In Season filtration time: 8-10 hours per day.
.
Off Season filtration time: 4-5 hours per day.
.
Example - variable speed pump (when running at
lower speeds):
In Season filtration time: 12-14 hours per day
In Season SWC time: 8-10 hours per day
Off Season filtration time: 10-12 hours per day
Off Season SWC time: 4-5 hours per day
Once validated, The SWC will adopt the same
timers as the filtration pump. The chlorination time
must be equal or shorter than the filtration time.
.
The device will not accept a SWC timer longer than
.
or outside the programmed filtration time.
7.3.1
Reset Timers
1.
Press
2.
Use
then press
3.
Use
The selected timers will be reset to 00:00.
7.3.2
Operation With an External Timer
In order for the controller to operate with an
external timer. All controller programs must be
cleared and the device must be on. After the
connection to the external timer is made, turn the
controller off then back on again.
7.3.3
Filter Pump Programming
1.
Press
2.
Use
then press
3.
Use
4.
Use
Timer 2" then press
5.
Use
to select the hour for the filtration on
time then press
6.
Use
to select the minutes for the filtration
on time then press
7.
Use
to select the hour for the filtration off
time then press
8.
Use
to select the minutes for the filtration
off time then press
9.
Press
EziSalt Saltwater Chlorinator | Installation Manual
.
to select "Programming"
.
to select "Reset Timers" then press
.
to select "Programming"
.
to select "Filter Pump" then press
to select "Pump Timer 1" or "Pump
.
.
.
.
.
to exit.
.
.
Advertisement
Table of Contents
