Kenwood NX-3720HG Service Manual page 62

NXDN Type Signaling
No. RX
1 RAN1
2 None
3 RAN1
7 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
RAN: Radio Access Number
PN9: Pseudo-Random Pattern
No.7, 9 Item: PC test mode only
DMR Type Signaling
No. RX
1 CC 00 Burst
2 PN9
3 CC 00 Burst
4 CC 00 Burst
5 CC 00 Burst
6 SYNC (Each Slot) +
PN9 Burst Pattern
7 SYNC (Super Frame) +
PN9 Burst Pattern
8 CC 00 Burst
9 Tone Pattern
10 Silence Pattern
11 Audio Test Pattern
12 Vocoder Loop
4.12 Panel Tuning Mode
4.12.1 Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [
is in test mode. Use the [
through tuning modes, and the [  ]/[  ] button to adjust tuning
requirements (1 to 4096 appears on the LCD).
Use the [ ] button to select the adjustment item through tuning
modes. Use the [ ] button to adjust 5 or 9 reference level
adjustments, and use the [  ] button to switch between Wide5k/
Wide4k/Narrow.
• LCD display in panel tuning mode
CV voltage, AD value, etc
L1
Sub LCD 2.6
display
An AST
Main LCD
display
An : Analog narrow mode
Aw : Analog wide 5k mode
As : Analog wide 4k mode
Nn : NXDN narrow mode Adjustment item
Nv : NXDN very narrow mode
D : DMR mode
1-62 (No.RA054<Rev.001>)
TX
RAN1
PN9
Maximum Deviation
Pattern
FSW + PN9
TX
CC 00 Burst
PN9
Maximum Deviation
Pattern
1/3 Deviation Pattern
0 Continuous Pattern
SYNC (Each Slot) + PN9
Burst Pattern
SYNC (Super Frame) +
PN9 Burst Pattern
0 Burst Pattern
Tone Test Burst Pattern
Silence Burst Pattern
Audio Test Burst Pattern
None
] button while the transceiver
(AUX)] button to write tuning data
256
Adjustment value
Adjustment point
(1~4096)
L1
Proper value guide
L2
(When the frequency
L3
adjustment is necessary,
C1
or is displayed.)
C2
C3
4.12.2 Button operation
Button
[+] Volume up
[-] Volume down
[  ] Adjustment value up
[  ] Adjustment value down
[  ] Auto adjustment start
[  ] Wide 5k/Wide 4k/Narrow/
NXDN/DMR
[ ] Shift to panel test mode
[ ] To enter 5 or 9 reference
level adjustments
[ ] Go to next adjustment
item
[ (AUX)] Writes the adjustment
value
[PTT] Transmit
(MIC)
[0] to [9] -
and
[#],[ ]
(MIC)
4.12.3 5 or 9 reference level adjustments frequency
Maximum Transmit Power, High Transmit Power, Medium
Transmit Power, Low Transmit Power, Balance, Maximum
Deviation , NXDN High Deviation, DMR High Deviation, QT
Deviation, DQT Deviation, LTR Deviation, DTMF Deviation,
Single Tone Deviation, MSK Deviation, CW ID Deviation, IQ
Phase, RSSI Reference, Squelch Open, Squelch Tight, Low
RSSI, High RSSI
Tuning point
1
2
3
4
5
H1
H2
H3
Function
Push Hold (1 second)
Continuation up
Continuation down
Continuation up
Continuation down
Output tone pattern
change of balance
adjustment (A change is
possible only during
balance adjustment.)
-
-
-
Back to last adjustment
item (At the time of 5 or 9
point adjustment:
Adjustment point change)
-
Display RX (MHz)
L1 136.05000
L3 145.55000
C2 155.05000
H1 164.55000
H3 173.95000
TX (MHz)
136.10000
145.60000
155.10000
164.60000
173.90000