Kenwood NX-3720HG Service Manual page 121

NXDN Type Signaling
No. RX
1 RAN1
2 None
3 RAN1
7 FSW + PN9
9 Tone Pattern (1031Hz) Tone Pattern (1031Hz)
RAN: Radio Access Number
PN9: Pseudo-Random Pattern
No.7, 9 Item: PC test mode only
DMR Type Signaling
No. RX
1 CC 00 Burst
2 PN9
3 CC 00 Burst
4 CC 00 Burst
5 CC 00 Burst
6 SYNC (Each Slot) +
PN9 Burst Pattern
7 SYNC (Super Frame) +
PN9 Burst Pattern
8 CC 00 Burst
9 Tone Pattern
10 Silence Pattern
11 Audio Test Pattern
12 Vocoder Loop
4.30 Panel Tuning Mode
4.30.1 Transceiver tuning (To enter tuning mode)
To enter tuning mode, press the [
is in test mode. Use the [
through tuning modes, and the [  ]/[  ] button to adjust tuning
requirements (1 to 4096 appears on the LCD).
Use the [ ] button to select the adjustment item through tuning
modes. Use the [ ] button to adjust 5, 9 or 17 reference level
adjustments, and use the [  ] button to switch between Wide5k/
Wide4k/Narrow.
• LCD display in panel tuning mode
CV voltage, AD value, etc
L1
Sub LCD 2.6
display
An AST
Main LCD
display
An : Analog narrow mode
Aw : Analog wide 5k mode
As : Analog wide 4k mode
Nn : NXDN narrow mode Adjustment item
Nv : NXDN very narrow mode
D : DMR mode
TX
RAN1
PN9
Maximum Deviation
Pattern
FSW + PN9
TX
CC 00 Burst
PN9
Maximum Deviation
Pattern
1/3 Deviation Pattern
0 Continuous Pattern
SYNC (Each Slot) + PN9
Burst Pattern
SYNC (Super Frame) +
PN9 Burst Pattern
0 Burst Pattern
Tone Test Burst Pattern
Silence Burst Pattern
Audio Test Burst Pattern
None
] button while the transceiver
(AUX)] button to write tuning data
256
Adjustment value
Adjustment point
(1~4096)
L1
Proper value guide
L2
(When the frequency
L3
adjustment is necessary,
L4
or is displayed.)
L5
L6
C1
C2
C3
4.30.2 Button operation
Button
[+] Volume up
[-] Volume down
[  ] Adjustment value up
[  ] Adjustment value down
[  ] Auto adjustment start
[  ] Wide 5k/Wide 4k/Narrow/
NXDN/DMR
[ ] Shift to panel test mode
[ ] To enter 5,9 or 17
reference level
adjustments
[ ] Go to next adjustment
item
[ (AUX)] Writes the adjustment
value
[PTT] Transmit
(MIC)
[0] to [9] -
and
[#],[ ]
(MIC)
4.30.3 5, 9 or 17 reference level adjustments frequency
Maximum Transmit Power, High Transmit Power, Medium
Transmit Power, Low Transmit Power, IQ Phase, RSSI
Reference, Squelch Open, Squelch Tight, Low RSSI, High
RSSI
Tuning point
1
2
3
4
5
Balance, Maximum Deviation, NXDN High Deviation, DMR
High Deviation, QT Deviation, DQT Deviation, LTR
Deviation, DTMF Deviation, Single Tone Deviation, MSK
Deviation, CW ID Deviation
Tuning point
1 L1
C4
C5
2 L3
H1
H2
3 L5
H3
H4
4 C1
H5
H6
5 C3
6 C5
Function
Push Hold (1 second)
Continuation up
Continuation down
Continuation up
Continuation down
Output tone pattern
change of balance
adjustment (A change is
possible only during
balance adjustment.)
-
-
-
Back to last adjustment
item (At the time of 5, 9 or
17 point adjustment:
Adjustment point change)
-
Display RX (MHz)
L1 400.05000
L5 417.55000
C3 435.05000
H2 452.55000
H6 469.95000
Display RX (MHz)
400.05000
408.85000
417.55000
426.35000
435.05000
443.85000
(No.RA054<Rev.001>)1-121
TX (MHz)
400.10000
417.60000
435.10000
452.60000
469.90000
TX (MHz)
400.10000
408.90000
417.60000
426.40000
435.10000
443.90000