Advertisement
How to Use my Truma Combi
6E Water and Heating System
A safe operating environment
– The unit may be operated only with appropriate Truma control panels
and accessories.
– Danger of toxic exhaust fumes. The heater's exhaust can be toxic in enclosed
spaces (e.g. garages, workshops).
What must I do if I smell gas?
– Extinguish all naked flames
– Open windows and doors
– Close all quick-acting valves and gas cylinders
– Do not smoke
– Do not operate any electrical switches
– Have the entire gas system checked by an expert.
If the vehicle is parked in closed rooms:
– Shut off the fuel supply to the heater
– Deactivate the time switch
– Switch off the heater at the control panel.
– If the cowl has been placed near or directly beneath an opening window, the appliance must be
equipped with an automatic shut-off device in order to prevent operation with the window open.
– Heat-sensitive objects (e.g. spray cans) or flammable materials/ liquids must not be stored in the
same compartment where the appliance is installed because, under certain conditions, this area may
be subject to elevated temperatures.
www.deluxegroup.co.nz
Advertisement
Table of Contents
Related Manuals for Truma Combi 6E
Summary of Contents for Truma Combi 6E
- Page 1 How to Use my Truma Combi 6E Water and Heating System A safe operating environment – The unit may be operated only with appropriate Truma control panels and accessories. – Danger of toxic exhaust fumes. The heater’s exhaust can be toxic in enclosed spaces (e.g.
-
Page 2: Obligations Of The Operator / Vehicle Owner
(e.g. the wardrobe door). Missing stickers can be requested from Truma. – Liquid gas systems must comply with the technical and administrative regulations of the respective country of use (e.g. -
Page 3: Operation While Driving
National regulations and rules must be followed. – If no safety shut-off device (e.g. as contained within the Truma MonoControl CS gas pressure regulation system) has been installed, the gas cylinder must be closed when driving and information signs must be attached in the gas cylinder protection box and in the vicinity of the control panel. -
Page 4: Maintenance / Repairs / Cleaning
– Modifications to the appliance (including accessories), – Modifications to the exhaust duct and the cowl, – Use of replacement and accessory parts other than original Truma parts, – Failure to follow the installation and operating instructions. The appliance’s operating permit, and consequently also the vehicle’s operating permit in some countries, are also rendered void. - Page 5 – or gas and electrical mode – mixed mode Only possible in winter. Heating and hot water mode In heating and hot water mode, the unit automatically selects the required operating level according to the temperature difference between the temperature set on the control panel and the current room temperature.
- Page 6 Read the safety instructions and operating instructions carefully before starting the unit. Operating instructions can be viewed in offline mode with a mobile device and the Truma App. Download the operating instructions when you have a WiFi connection and save them on your mobile device.
- Page 7 Truma supplies a heating element (part no. 70070-01) as an accessory, which is inserted into the FrostControl and fixed in place with a retaining bracket. This heating element heats the FrostControl to approx.
- Page 8 Operating instructions Filling the boiler Check whether the safety/drain valve is closed (see “Closing the safety/drain valve”). When the temperature at FrostControl is below approx. 7 °C, first switch on the heater to warm the installation compartment and FrostControl. After several minutes, when the temperature at FrostControl is above 7 °C, the safety/drain valve can be closed.
-
Page 9: Maintenance
Maintenance Only original Truma parts may be used for maintenance and repair work. – Clean the compartment where the unit is installed at least once annually. – Have an expert check the unit for dirt and clean it if necessary. - Page 10 Once the water in the boiler has reached a temperature of 60 °C, the burner will switch off. The appliance must stay switched on for at least 30 minutes and no hot water may be removed. The residual heat in the heat exchanger will heat the water up to 70 °C.
- Page 11 Faults Faults Heater Descriptions of possible fault causes and a troubleshooting guide can be found in the operating instructions for the control panel that is installed. Faults – Water supply Possible fault causes and a troubleshooting guide – See “Troubleshooting guide (water supply)”. Troubleshooting guide (water supply) Fault Cause/Remedy...