ATTO Technology FastStream SC 5300 Installation And Operation Manual page 58

RGResumeConversion
Continues the stopped conversion on the specified RAID group.
RGResumeConversion [GroupName]
RGResumeErase
Continues the erase on the specified RAID group.
RGResumeErase [GroupName]
RGResumeInitialization
Continues a stopped initialization for the specified RAID group.
Set RGresumeInitialization [GroupName]
RGResumeRebuild
Continues the rebuild(s) on the specified RAID group. If no
MemberIndex is specified, all stopped rebuilds on that RAID
group are resumed.
RGResumeRebuild [GroupName] <MemberIndex>
RGSectorSize
Sets or displays the sector size of the specified RAID Group.
The desired RAID Group sector size must be evenly divisible by
the sector size of any member disk. 512 bytes is the default size
for most operating systems. Use 4 KB sectors to enable large
volume support (greater than 2 TB) in Windows XP (32-bit).
Default: 512
set RGSectorSize [GroupName] [512-8192]
get RGSectorSize [GroupName]
RGSpanDepth
Regulates or displays the span depth on the specified RAID
group. The RAID group must be of type RAID 0, 1, 4, 5, 6 or 1+0.
set RGSpanDepth [GroupName] [SpanDepth [1-16]]
get RGSpanDepth [GroupName]
RGSpeedRead
Performs look-ahead during reads from RAID group
member disks for all or the specified RAID group.
Default: auto
set RGSpeedRead [GroupName | all] [enabled | disabled
| auto ]
get RGSpeedRead [GroupName | all]
RGUnmap
Removes all mapped partitions for a RAID group from the
routing table. The partitions themselves are unaffected,
although they are inaccessible to initiators.
RGUnmap [GroupName | all]
xiv
ATTO Technology Inc. FastStream SC Installation and Operation Manual
RGWaitTimeout
Specifies the maximum time in seconds that the system waits to
discover previously-configured RAID groups attached to the
unit. The time out is used during system boot time and when the
BlockDevScan command is issued.
Default: 5
set RGWaitTimeout [1-3600]
SaveConfiguration Restart command required
get RGWaitTimeout
RMStatus
Displays the status of all RAID members within the specified
RAID group or a particular RAID member if specified within the
specified RAID group.
RMStatus [GroupName] <MemberIndex>
Route
SC 5300
Assigns a host protocol address to a target destination device.
More than one FC LUN may be assigned to a partition. If you try
to map a new partition to the same FC LUN, the previous map
is overwritten. Use the delete identifier to remove the map. In
verbose mode, overwriting a map requires secondary
confirmation of the action.
If FCMultiNode is disabled: Route FC [lun] [RAID
[GroupName] [PartIndex]] | Delete]
If FCMultiNode is enabled: Route FC [fp] [lun] [RAID
[GroupName] [PartIndex]] | Bridge | Delete]
Route
SC 5700
Assigns a host protocol address to a target destination device.
More than one FC LUN may be assigned to a partition. If you try
to map a new partition to the same FC LUN, the previous map
is overwritten. Use the delete identifier to remove the map. In
verbose mode, overwriting a map requires secondary
confirmation of the action.
You may also map pass through devices.
If FCMultiNode is disabled: Route FC [fl] [RAID
[GroupName] [PartIndex]] |FC [fp] [Index]] | Delete]
If FCMultiNode is enabled: Route FC [fp] [fl] [[RAID
[GroupName] [PartIndex]] |FC [fp] [Index]] | Delete]
RouteDisplay
Displays a combined list of host protocol address to target
destination device mappings.
If FCMultiNode is disabled: RouteDisplay [FC] <lun> |
passthrough | persistent>
If FCMultiNode is enabled: RouteDisplay [FC] <<fp>
<lun>> | passthrough | persistent>