Table of Contents
Advertisement
Purpose of this manual ............................................................ 3 (E)
Related manuals ...................................................................... 3 (E)
Trademarks .............................................................................. 3 (E)
1-1.
Service Flow Chart ....................................................1-1 (E)
1-1-1.
Flow Chart before Service ...............................1-1 (E)
1-1-2.
Flow Chart after Service ..................................1-3 (E)
1-2.
Precaution for Transporting .......................................1-4 (E)
1-3.
Board Location and Main Parts Location .................1-5 (E)
1-3-1.
Board Location ................................................1-5 (E)
1-3-2.
Main Parts Location .........................................1-5 (E)
1-3-3.
Sensor Location ...............................................1-6 (E)
1-4.
Tightening torque ......................................................1-6 (E)
1-5.
Removing/Installing the Cabinet ...............................1-7 (E)
1-5-1.
Top Cover ........................................................1-7 (E)
1-5-2.
Front Panel Block Assembly ...........................1-8 (E)
1-5-3.
Rear Panel ......................................................1-10 (E)
1-6.
General Information of Utility Software ................. 1-11 (E)
1-6-1.
Required Equipment/Tools ............................ 1-11 (E)
1-6-2.
Preparation ..................................................... 1-11 (E)
1-6-3.
Function Description......................................1-12 (E)
1-7.
Firmware Version Upgrade .....................................1-21 (E)
1-8.
Service Mode...........................................................1-22 (E)
1-8-1.
Startup Procedure ...........................................1-22 (E)
1-8-2.
Service Mode Menu .......................................1-22 (E)
1-9.
Menu Lock Function ...............................................1-26 (E)
1-10. Lithium Battery (UP-X898MD) ..............................1-27 (E)
1-11. Cleaning ..................................................................1-28 (E)
1-11-1.
Cleaning the Cabinet ......................................1-28 (E)
1-11-2.
Cleaning the thermal head .............................1-28 (E)
1-11-3.
Cleaning the Platen Roller .............................1-29 (E)
1-12. Periodic Inspection and Periodic
Replacement Parts ...................................................1-30 (E)
1-13. Print Size .................................................................1-30 (E)
1-13-1.
Rough Standard of Print Size.........................1-30 (E)
1-13-2.
Interval Between Print Screens ......................1-31 (E)
1-13-3.
Blank in Horizontal Direction........................1-31 (E)
1-14. Lead-free Solder ......................................................1-31 (E)
UP-D898MD/X898MD
Table of Contents
2-1.
Error Log Acquisition Procedure ..............................2-1 (E)
2-1-1.
2-2.
Trouble Flow Chart ...................................................2-3 (E)
2-2-1.
2-2-2.
2-2-3.
2-2-4.
2-2-5.
2-2-6.
2-2-7.
2-2-8.
2-2-9.
2-2-10.
2-2-11.
2-2-12.
2-2-13.
3-1.
MA-195 Board ..........................................................3-2 (E)
3-1-1.
3-1-2.
3-1-3.
3-1-4.
3-1-5.
3-1-6.
3-2.
KY-711 Board..........................................................3-10 (E)
3-3.
SE-1142 Board ........................................................3-12 (E)
3-4.
SE-1143 Board ........................................................3-13 (E)
Error Code Table ..............................................2-1 (E)
power switch is turned on ................................2-3 (E)
Print density is too high or too low ..................2-9 (E)
Feed operation failure ....................................2-10 (E)
Door open/close operation failure..................2-12 (E)
Flow Chart .......................................................3-2 (E)
Saving of Setting Value ....................................3-3 (E)
Sample (Step) Printing .....................................3-4 (E)
Replacement Procedures of MA-195 Board ....3-5 (E)
Setting and Check of Setting Value .................3-7 (E)
Density Adjustment (Thermal Head Voltage
Adjustment) and Set Serial Number Setting ....3-8 (E)
1 (E)
Advertisement
Table of Contents
