Ametek Land LMG GS User Manual page 3

Important Health and Safety Information
Equipment Operation
Use of this instrument in a manner not specified by Land Instruments International may be hazardous.
Electrical Power Supply
Before working on the electrical connections all of the electrical power lines to the equipment must be isolated. All the
electrical cables and signal cables must be connected exactly as indicated in these operating instructions. If in doubt
contact Land Instruments International.
Face and Eye Protection
Suitable face and eye protection must be worn when working on hot vessels and ducts! Special safety measures must be
taken when working on a high-pressure duct.
Protective Clothing
Protective clothing must always be worn when working in the vicinity of hot vessels or ducts.
Storage
The instrument should be stored in its packaging, in a dry sheltered area.
Unpacking
Check all packages for external signs of damage. Check the contents against the packing note.
Return of Damaged Goods
IMPORTANT
If any item has been damaged in transit, this should be reported to the carrier and to the supplier immediately. Damage
caused in transit is the responsibility of the carrier not the supplier.
DO NOT RETURN a damaged instrument to the sender as the carrier will not then consider a claim. Save the packing with
the damaged article for inspection by the carrier.
Return of Goods for Repair
If you need to return goods for repair please contact our Customer Service Department. They will be able to advise you on
the correct returns procedure.
Any item returned to Land Instruments International should be adequately packaged to prevent damage during transit.
You must include a written report of the problem together with your own name and contact information, address,
telephone number, email address etc.
Return of Goods for Repair Form is available for download from our websites.
Lifting Instructions
Where items are too heavy to be lifted manually, use suitably rated lifting equipment. Refer to the Technical Specification
for weights. All lifting should be done as stated in local regulations.
Design and Manufacturing Standards
Approvals apply in the USA
This instrument complies with current European directives relating to
Electromagnetic Compatibility 89/336/EEC and Low Voltage Directive
73/23/EEC.
Operation of radio transmitters, telephones or other electrical/electronic devices in
close proximity to the equipment while the enclosure doors of the instrument or its
peripherals are open, may cause interference and possible failure where the radiated
emissions exceed the EMC directive.
The protection provided by both CE and IP classifications to this product may be
invalidated if alterations or additions are made to the structural, electrical, mechanical
or pneumatic parts of this system. Such changes may also invalidate the standard terms
of warranty.
Dimensions
Unless otherwise stated, all measurements are given in millimetres and inches.
Copyright
This manual is provided as an aid to owners of Land Instruments International's products
and contains information proprietary to Land Instruments International. This manual may
not, in whole or part, be copied, or reproduced without the expressed written consent
of Land Instruments International Ltd.
Copyright © 2007 - 2010 Land Instruments International.
IMPORTANT INFORMATION - PLEASE READ
The Quality Management System of
Land Instruments International is approved
to BS EN ISO 9001 for the design,
manufacture and on-site servicing of
combustion, environmental monitoring and
non-contact temperature measuring
instrumentation.
Signs and Symbols Used on
Equipment and Documentation
Caution, risk of electric shock.
This item or material can be recycled.
Caution, attention to possibility of risk of damage to the product,
process or surroundings. Refer to instruction manual.
Caution, hot surface.
This item or material can be recycled.
This item or material must be disposed of in accordance
with the Waste Electrical and Electronic Equipment
directive as applied by local regulations.
Protective Conductor Terminal.
Observe precautions for handling electrostatic discharge
sensitive devices.
Office Locations
UK - Dronfield
Tel: +44 (0) 1246 417691
E-Mail: land.infrared@ametek.co.uk
Web: www.landinst.com
USA - Pittsburgh
AMETEK Land, Inc.
Tel: +1 412 826 4444
E-Mail: irsales@ametek.com
Web: www.ametek-land.com
For further details on all LAND/
Ametek offices, distributors and
representatives, please visit our
websites.