Table of Contents
Advertisement
Integra
Luxtec
®
UltraLite® Plus Headlight
Replacement Parts for Ultralite® Plus Headlight
Part Number
Description
AX1375BIF
Headband with Ultralite 2 bifurcated cable, Ultralite module and extended linkage
AX1385BIF
Sweatband with Ultralite 2 bifurcated cable, Ultralite module and extended linkage
AX1375BIFSL
Headband with Ultralite 2 bifurcated cable and Ultralite module
AX1385BIFSL
Sweatband with Ultralite 2 bifurcated cable and Ultralite module
001170BIF
Replacement headband for AX1175SBIF
001190EL
Module (gray) with extended linkage
001270BIF
Replacement headband for AX1375BIF or AX1375BIFSL
001290BIF
Replacement sweatband for AX1375BIF or AX1375BIFSL
400282LX
Replacement kit pad for headband
0o0286
Joystick for 001190, pack of 3
Care and Maintenance
All Headlight Systems:
To ensure long life for the headband, cable, and modules,
they should be stored in the duffel bag or case provided. Fiber
optic cables are fine, high quality optical instruments. You can
prolong the useful life by following a few guidelines:
• Avoid stretching your cable, forming configurations
involving sharp angles or kinks, or contact with sharp or
pointed objects. The internal light fibers are made of glass,
a material which breaks under stress. Fiber breakage will
result in diminished light output.
• Utilize the gown clips (If provided) to keep the
headlight cable secured to the surgeon's gown for greater
comfort and maneuverability. (This does not include
endoscopic use)
• Do not use your fiber optic cable with any alterations to it's
original design or fabrication. Bundle size (aperture) of the
fiber optic cable should be matched to the aperture of the
instrument to obtain maximum light output.
• NOTE: A larger aperture fiber optic cable will not increase
light output of a smaller aperture instrument.
• Keep the optical faces from contacting the floor or other
hard surfaces. The resulting scratches will diminish light
output. Store the cables in sterilization trays for
additional protection.
• Any inadvertent cut or puncture to the silicone tube will
render the cable unsafe. It should be taken out of
service immediately.
Cleaning Modules:
The headlight module may be wiped down with alcohol. The
lens should be cleaned only with lens tissue available at any
camera store. Follow the package directions.
7
®
Follow all applicable bloodborne pathogen cleaning
procedures as indicated by OSHA and / or your
hospital requirements when cleaning, disinfecting,
and sterilizing instruments and accessories.
Cleaning Joystick (only):
The joystick can be removed from the module for autoclaving.
Cleaning Sweatband:
The sweatband may be cleaned using standard wash
cycles in warm water and detergent. Air dry.
Cleaning Headband:
The headband may be cleaned by an alcohol wipedown or
washed with lukewarm water and mild detergent. Rinse
thoroughly with water.
Cleaning Cable:
Wipe the fiber optic cable sheathing with a water dampened paper
towel, cloth, or gauze before using 70 % Alcohol as the disinfectant.
Disinfecting Cable:
Soaking the UltraLite 2 cables in any sterilizing disinfectant
should be avoided. There is a lens assembly at the light source
end, which is not sealed and could allow moisture to penetrate
behind the lensing.
Sterilizing Cable:
The UltraLite fiber optic cable has not been specifically
designed to withstand sterilization. There is a lens assembly
at the light source end, which is not sealed and could allow
moisture to penetrate behind the lensing.
WARNING: Do not autoclave the headband,
cables, sweatband or headlight modules.
Advertisement
Table of Contents
