Page 1
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e MLX 300 WATT XENON LIGHT SOURCE Operation and Service Manual ENGLISH 99 hartwell street west Boylston, Ma 01583 usa tel: +1-508-835-9700 us toll Free: 1-800-325-8966 Fax: +1-508-835-9976 website: http://www.integra-surgical.com e-mail: custsvcluxtec@integra-surgical.com...
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e TAbLE Of CONTENTS PAGE DESCRIPTION indication For use symbols general warnings Precautions overview operation Xenon Lamp Module replacement Fuse replacement optional Floor stand assembly...
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e INDICATION fOR USE The Luxtec MLX light source is designed to supply high-intensity white light to a fiber optic cable for illumination of a surgical field during a surgical and/or medical procedure.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e SYMbOLS taBLe oF sYMBoLs Found on a medical grade light source, other illumination related equipment, fiber optic cables and corresponding packaging. attention; consult accompanying Documents Fuse caution: high Voltage type cF equipment equipotentiality...
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e GENERAL WARNINGS • The user should carefully study the Operation • Explosion Hazard. Do not use in the presence of and service Manual before using the equipment flammable anesthetics, liquids, vapors, gases or dusts. in a clinical environment. instructions should be followed, with special attention given to warnings, • Keep cooling vent and fans free of obstructions.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e OVERVIEW The MLX light source delivers 300 spare watts of cool white infrared (IR) filtered light. The lamp is housed in a lamp module that can be easily serviced without special tools. set up and inspection Before use the light source comes with the hospital grade power cord packaged separately.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e OPERATION 5. the system will start up at the same light intensity as when last used (Figure 3). For new systems, the light intensity will start at the minimum 20% setting.
Page 8
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e XENON LAMP MODULE REPLACEMENT to remove: 1. Make sure the power is off and the hospital grade power cord is disconnected. 2.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e fUSE REPLACEMENT to replace the fuse: • The fuse for the light source is located in the power entry module in the rear of the unit. • Remove the hospital grade power cord from the back of the light source. • Using a small flat screwdriver, pry open the retaining door (Figure 8)and pry out the red plastic block from the power entry module (Figure 9).
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e OPTIONAL fLOOR STAND ASSEMbLY There are four (4) parts to the floor stand assembly: (Figure 10). (Phillips head screwdriver included for assembly) 1. Base with five (5) casters (2 locking) 2.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e REPLACEMENT PARTS AND ACCESSORIES to place an order, contact your local Luxtec distributor or call Luxtec customer service at 1-800-325-8966 (usa &...
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e ELECTROMAGNETIC COMPATIbILITY (EMC) USER INfORMATION warning: Medical electrical equipment needs special precautions regarding eMc and needs to be installed and put into service according to the electromagnetic compatibility [eMc] information provided in the accompanying documents.
Page 15
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e ELECTROMAGNETIC COMPATIbILITY (EMC) USER INfORMATION table 202 Guidance and Manufacturer’s Declaration—Immunity All Equipment and Systems the MLX light source is intended for use in the electromagnetic environment specified below. the customer or user of the MLX light source should assure that it is used in such an environment.
Page 16
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e ELECTROMAGNETIC COMPATIbILITY (EMC) USER INfORMATION table 204 Guidance and Manufacturer’s Declaration – Emissions Equipment and Systems that are not Life-supporting the MLX light source is intended for use in the electromagnetic environment specified below. the customer or user of the MLX light source unit should ensure that it is used in such an environment.
M L X 3 0 0 w a t t X e n o n L i g h t s o u r c e REPAIR AND RETURN INfORMATION this device must be clean and decontaminated prior to return to Luxtec. Luxtec reserves the right to return unrepaired any equipment that is contaminated with blood or other organic material.