Savant Pro Remote Multi-Room Quick Reference Manual page 2

Additional Information
– Automatic software updates to the Remote will initiate if it is left
cradled overnight, with no A/V services active, and a cloud user is
signed in.
– Software updates can be initiated manually from the About page on
the Remote (only if update is available).
Network Requirements
Savant requires a wireless network that is configured to make use of at
least one of the supported wireless standards listed in the
Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured. Savant
recommends using DHCP reservation within the router. By using this
method, static IP Addresses for all devices can be managed from a
single UI, avoiding the need to access devices individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Refer to the Savant Pro Remote Deployment Guide (009-1531-xx)
located on the Savant Community for information on connecting the
Pro Remote Base to the local network.
Additional Documentation
Additional documentation available on the Savant Customer
Community.
– Savant Pro Remote Deployment Guide (009-1531-xx)
– Savant Pro Remote User Guide (009-1410-xx)
Part# HDH6A005010
REM-2000/REM-2000I | 009-1530-01 | 171027
Copyright 2017 Savant Systems, LLC
FCC INTERFERENCE STATEMENT: Pro Remote
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference, and
1.
This device must accept any interference received, including interference that may cause
2.
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Identifier for Pro Remote
This device electronically displays the FCC declaration of conformity logo as well
as the FCC and IC identifier. This information can be found on the device by accessing:
(main menu) Settings
Identificateur de la FCC et d'IC pour Pro Remote
Ce périphérique par voie électronique affiche le logo de déclaration de conformité
FCC ainsi que l'identificateur de la FCC et d'IC. Cette information peut être trouvée sur
le terminal en accédant à:
(A propos de).
Radiation Exposure Statement: Pro Remote
This device meets the government's requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of the
U.S. Government.
The exposure standard for wireless device employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR
are conducted using standard operating positions accepted by the FCC with the device
transmitting at its highest certified power level in all tested frequency bands.
INDUSTRY CANADA STATEMENT: Pro Remote
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
This device may not cause interference, and
1.
This device must accept any interference, including interference that may cause undesired
2.
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
L'appareil ne doit pas produire de brouillage, et
1.
L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
2.
brouillage est susceptible d'en compromettre le fonctionnement.
– This Class B digital apparatus complies with Canadian ICES-003.
– Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
– This device complies with RSS-310 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
– Cet appareil est conforme à la norme RSS-310 d'Industrie Canada. L'opération est soumise
à la condition que cet appareil ne provoque aucune interférence nuisible.
– This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter, except tested built-in radios. The County Code Selection
feature is disabled for products marketed in the US/Canada.
– Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec
une autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été
testées. La fonction de sélection de l'indicatif du pays est désactivée pour les produits
commercialisés aux États-Unis et au Canada.
Radiation Exposure Statement: Pro Remote
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operate with minimum distance
20cm between the radiator and your body.
Déclaration d'exposition aux radiations: Pro Remote
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnementnon contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
2 of 2
About.
(menu principal) Settings (Paramètres)
45 Perseverance Way, Hyannis, MA 02601
Savant.com
About
| 508.683.2500