Detection Zone; Technical Specifications - STEINEL IR Quattro SLIM Series Manual

How it works / Basic function
The infrared presence detectors sons. The pyro-sensor with highly
from the Control PRO range con- advanced lens provides a square
trol lighting as well as heating, detection zone, as the typical
ventilation and air-conditioning shape of a room, in which the
(COM 2 only), e.g. in offices, smallest of movements are
schools, public buildings or at sensed. The presence detector's
home, in relation to ambient light switching outputs are set using
level and the presence of per- the remote controls RC 5 and RC 8.
IR Quattro SLIM COM 1 IR Quattro SLIM DIM
1 switching output operating in 1 switching output operating in
relation to brightness setting relation to brightness setting
and presence of persons. and presence of persons.
IR Quattro SLIM COM 2
1 switching output as COM 1.
An additional 2nd switching out-
put for operating HVAC (heating/
ventilation/air-conditioning)
in relation to the presence of
persons.

Detection zone

presence
radial
tangential
2.5 m 2.8 m 3.5 m 4 m
tangential 4 m 4 m 5.5 m 6 m
radial 3.2 m 4 m 4 m 5 m
presence 3.8 m 4 m 4.5 m
Presence Control has a low
intrinsic power consumption.
IR Quattro SLIM DALI
2 DALI switching outputs operat-
ing in relation to brightness set-
ting and presence of persons.
Settings:
- Brightness setting
- Stay-ON time, IQ mode
- Orientation light
(DIM/DALI only)
- Constant lighting control
(DIM/DALI only)
- Scenario control (DALI only)
tangential
radial
presence
The square detection zone and the ability to inter-
connect the master/slave versions provide the
basis for creating optimum configurations quickly
and easily.
–
- 18 -
Electrical installation / Automatic mode
In selecting the wiring leads, it is lead containing both the mains
important to meet the wiring voltage leads and the control
regulations laid down in VDE leads (e.g. NYM 5 x 1.52) may be
0100 (see Safety warnings on used for the wiring between
page 17). Wiring up the pres- sensor and electronic ballast.
ence detector: Under section 6 of The mains connection lead must
VDE 0100 520, a multiple-core be no greater than 10 mm in

Technical specifications

Dimensions (W x H x D): load module
61.3 x 126.5 x 42.5 mm
Power supply: 120 – 250 V, 50 Hz / 60 Hz
Capacity, switching output 1: 230 V
(COM 1/COM 2) 2000 W max. resistive load (cos φ = 1)
1000 VA max. (cos ϕ = 0.5)
120 V
Resistive load 1000 W max. (cos ϕ = 1)
500 VA max. (cos φ = 0.5)
Electronic ballast max. inrush current 800 A/200 μs
(COM 1/COM 2/DIM) 30 x (1 x 18 W), 25 x (2 x 18 W)
25 x (1 x 36 W), 15 x (2 x 36 W)
20 x (1 x 58 W), 10 x (2 x 58 W)
Note: each electronic ballast has its own particular inrush
current. A relay or contactor must be provided on line side
for higher switching capacities.
Capacity, switching output 2: Presence
(COM 2 only) 230 W/230 V max. / 120 W/120 V max.
1A max. (cos ϕ = 1) for HVAC
(heating/ventilation/air-conditioning)
Square detection zones: IR Quattro SLIM
Presence: 4 x 4 m max. (16 sq.m.)
Radial: 4 x 4 m max. (16 sq.m.)
Tangential: 4 x 4 m max. (16 sq.m.)
Light-level setting: 10 – 1000 lux, ∞ / daylight /
DIM 100 – 1000 lux control threshold
Switching output 1:
1 – 15 min.
Time setting IQ mode time (automatic adjustment to usage profile)
Switching output 2: only COM2 for HVAC
Time setting 0 or 10 min. switch-ON delay
5/10/15 min. stay-ON time (factory setting: 5 min.)
Automatic room surveillance
DIM:
Basic brightness: 10 %
Control output: 1 – 10 V / 50 electronic ballasts max., 100 mA max.
DALI:
Basic brightness: 10 %
DALI output 1 / output 2 2-core DALI control cable / broadcast
Time setting: OFF / 10/30 min. / all night
Mounting height (ceiling mounting): 2.5 m – 4 m
Point of installation: indoors
IP rating: IP 20
Protection class: II
Temperature range: 0 °C to +40 °C
diameter. The mains connection
terminal accepts 2 x 2.5 mm
cables. When installing the
presence detector, connect
a circuit breaker (16 A)
on the line side.
sensor module
77 x 77 x 60 mm
- 19 -
2