Table of Contents
Advertisement
en ENGLISH
machine switches off. Switch machine off with
switch. Switch it on again and continue to work as
normal. Try to prevent the machine from seizing.
See chapter 4.2.
Machines with VIC and TC electronics·
I'\
The electronic signal display (10) lights
0
up and the load speed decreases.
- too much load on the machine! Run the
machine in idling until the electronics signal
indicator switches off.
Machines with VIC, TC and
>.,
The electronic signal display (10) flashes
't
and the machine does not start.
..... protection is active. If the mains plug is
inserted with the machine switched on, or if the
power supply is restored following an interruption,
the machine does not start up. Switch the machine
off and on again.
11 . Accessories
Use only genuine Metabo accessories.
See page 5.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Safety guard for cut-off grinding
Designed for work with cutting disc and diamond
cutting discs.
Install as described under "Safety guard for
grinding" (chapter 6.2).
B Hand guard for sanding and wire brushing
operations
Designed for work with support plates, sanding
pads, wire brushes.
Install hand guard under the additional side
mounted handle.
C Dust filter
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
D Multiple position bar for side handle
Permits numerous handle positions.
See www.metabo.com or the catalogue for a
complete range of accessories.
12. Repairs
� Repairs to electrical tools must ONLY be
[.;__J carried out by qualified electricians!
If the connection lead is damaged, it must be
replaced by a special connection lead.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
11
13. Environmental Protection
The generated grinding dust may contain harmful
substances. Do not dispose with household trash;
dispose of properly at a collection point for
hazardous waste.
There is
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
vc
Only for EU countries: Never dispose of
electronics·
power tools in your household waste! In
accordance with
The restart
European Directive 2012/19/EU relating to elec
trical and electronic waste
and implementation of national law, used electrical
tools must be collected separately and disposed of
in an environmentally friendly manner at recycling
centres.
14. Technical Data
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
0
t max,2
t max,3
M
I
n*
n v *
P
1
P 2
m
Measured values determined in conformity with
EN 60745.
[g] Machine in protection class II
- AC Power
* Machines with the designation WE ... : Energy-rich,
high-frequency interference can cause fluctuations
in speed. The fluctuations disappear, however, as
soon as the interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
� Emission values
[.;__J These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user e.g. organisational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a h sG
'
a h, DS
= max. diameter of the accessory
max. permitted thickness of clamping
shank on accessory when using (tool
free) clamping nut (2)
roughing disc/cutting disc:
max. permitted thickness of accessory
= spindle thread
= length of the grinding spindle
= no-load speed (maximum speed)
= no-load speed (adjustable)
= Rated input power
= Power output
= Weight without mains cable
= Vibration emission value
(surface grinding)
= Vibration emission value
(sanding with sanding plate)
Advertisement
Table of Contents
