Cleaning & Maintenance; Environmental Protection; Technical Specifications - Metabo FSX 200 Intec Original Instructions Manual

6.1 Installation of sanding disc
Simple attachment and removal thanks to the
velcro-type fastening.
Simply press on the sanding disc such that the
holes in the sanding disc (1) are aligned with the
support plate (2).
7. Use
7.1 Switching On and Off
Switching on:
Move switch (3) to "I" position.
Switching off:
Move switch (3) to "O" position.
7.2 Dust Extraction
To optimise the dust extraction performance, fit the
sanding disc such that the holes on the sanding disc
(1) are aligned to the support plate (2).
Integrated extraction system:
Install the dust collection box (4) (see illustration,
page 2). To optimise the extraction performance,
empty the dust collection box (4) in good time and
clean the filter (6).
External extraction system:
Fit dust extraction nozzle (see chapter on
Accessories). Connect a suitable extraction device.
Use a suction hose with a 35 mm connector
diameter. See Accessories section.
8. Cleaning, Maintenance
Empty dust collection box (4).
- Open cleaning flap (5).
- Empty dust collection box (4).
- Remove fluted filter (6) and knock off dust stuck to
filter or remove with brush.
- When inserting, ensure that the fluted filter (6) is
inserted in the lateral guides.
Clean the machine regularly. This includes
vacuum cleaning the ventilation louvres on the
motor.
Replacing a worn support plate (2)
- Remove fixing screws (on lower side of support
plate).
- Remove support plate.
- For replacement support plates, refer to the
Accessories chapter.
- Mount support plate.
- Refit fixing screws (on lower side of support plate)
and tighten.
Replacing support plate brake / braking ring
If the idling speed of the support plate increases in
the course of time, the braking ring is worn and must
be replaced in a service workshop for Metabo
power tools.
Note: If abrasive material (e.g. gypsum, etc.) is
being sanded, the braking ring inevitably wears
faster.
9. Accessories
Use only genuine Metabo accessories.
See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Support plate with velcro-type fastening
(as replacement)
B Adhesive intermediate disc
C Adhesive sanding discs
D Adhesive polishing sponge
E Lambskin adhesive polishing disc
F Adhesive polishing felt
G Adhesive sanding fleece
H Adhesive sanding screen
I Fluted filter (as replacement)
J Dust collection box (as replacement)
K Dust extraction connection
L Metabo universal vacuum cleaner
For complete range of accessories, see
www.metabo.com or the main catalogue.
10. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

11. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.

12. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
D = Dimensions of sanding plate
P = Nominal power input
1
P = Power output
2
n = Idle speed
0
n = Speed at rated load
1
s = Orbital frequency at no load
0
s = Orbital frequency at nominal load
1
S = Oscillating circuit diameter
Intec = Dust collection box
m = Weight without mains cable
ENGLISH en
9