Table of Contents
Advertisement
en ENGLISH
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Clip to tighten/release the (tool-free) clamping
nut manually *
2 Clamping nut (tool-free) *
3 Support flange
4 Spindle
5 Spindle locking button
6 Safety cover
7 Side handle/Additional handle with vibration
damping *
8 Sliding on/off switch *
9 Handle
1 O Electronic signal indicator
11 Speed adjustment wheel *
12 Switch-on lock*
13 Trigger switch *
14 Lever for safety guard attachment
* depending on equipment/not in scope of delivery
6. Commissioning
..,. Before plugging in, check that the rated mains
� voltage and mains frequency, as stated on the
type plate match your power supply.
..,. Always install an RCD with a maximum trip
� current of 30 mA upstream.
6.1
Attaching the additional handle
..,. Always work with the additional handle (7)
� attached! Attach the additional handle on the
left or right of the machine and secure.
6.2
Attach the safety guard
..,. For safety reasons, always use the safety
� guard provided for the respective wheel! See
also chapter 11. Accessories!
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cutting discs.
See illustration C on page 2.
- Place the safety guard (6) in the position
indicated.
- Push the lever (14) and turn the safety guard until
the closed section is facing the operator.
- Release lever and rotate guard
until the lever latches.
- Make sure that the guard is placed securely: The
lever must engage and you should not be able to
turn the safety guard.
9
�1/
Use only accessories that
c:::o:::x
are covered by at least 3.4
mm by the safety guard.
(Disassemble in reverse
order.)
7. Attaching the grinding wheel
..,. Prior to any conversion work: Pull the mains
� plug from the socket. The machine must be
switched off and the spindle at a standstill.
..,. For reasons of safety, attach the cut-off
� grinding guard before performing cut-off
grinding work (see Chapter 11. Accessories).
7.1
Locking the spindle
..,. Press in the spindle locking button (5) only
� when the spindle is stationary.
- Press in the spindle locking button (5) and
turn the spindle (4) by hand until the spindle
locking button engages.
7.2
Placing the grinding wheel in position
See illustration B on page 2.
- Fit the support flange (3) on the spindle. The
flange should not turn on the spindle when
properly attached.
- Place the grinding wheel on the support flange (3).
The grinding wheel must lay flat on the supporting
flange.
7.3
Securing/releasing the (tool-free)
clamping nut
..,. Only tighten the (tool-free) clamping nut (2) by
�hand!
..,. For the machine to operate, the clip (1) must
� always lie flat on the clamping nut (2) .
To secure the (tool-free) clamping nut (2):
..,. Use only accessories which fulfil the
�specifications.See Chapter 14. Technical
Data) .
- Lock the spindle (see chapter 7.1 ).
- Flip up the clip (1) on the clamping nut.
- Fit the clamping nut (2) on the spindle (4). See
illustration A on page 2.
- Tighten the clamping nut on the clip (1) manually
in a clockwise direction.
- Flip down the clip (1) again .
Release the (tool-free) clamping nut (2):
- Lock the spindle (see chapter 7.1 ).
- Flip up the clip (1) on the clamping nut.
- Unscrew the clamping nut (2), turning it
anticlockwise manually
N.o1e.: If the clamping nut (2) is very tightly secured,
you can also use a 2-hole spanner to unscrew it.
Advertisement
Table of Contents
