Videx ESVK Manual page 11

ESVK/KRV86 - ESVK/KRV88 Series "2 wire Bus" videokit
Art. 4384
Speaker unit with built-in camera
Art. 4384X
Speaker unit with built-in camera & proximity key reader
PROGRAMMING
The programming consists of the following settings:
• Unit ID (1..15);
• Door opening time (2 or 6 seconds);
• Conversation time (1 or 2 minutes);
• Addressing order of the buttons.
• Main camera selection for Art. 4384 versions or programming mode for Art. 4384X versions.
The settings are carried out through the 8 way dip-switch (reference
PROGRAMMING THE UNIT ID
Switch Nr.1 Nr.2 Nr.3 Nr.4
ON
OFF OFF OFF OFF
1 2 3 4 5 6 7 8
ON
ON OFF OFF OFF
1 2 3 4 5 6 7 8
ON
OFF ON OFF OFF
1 2 3 4 5 6 7 8
ON
ON
1 2 3 4 5 6 7 8
ON
OFF OFF ON OFF
1 2 3 4 5 6 7 8
ON
ON OFF ON OFF
1 2 3 4 5 6 7 8
ON
OFF ON
1 2 3 4 5 6 7 8
ON
ON
1 2 3 4 5 6 7 8
ON
OFF OFF OFF ON
1 2 3 4 5 6 7 8
ON
ON OFF OFF ON
1 2 3 4 5 6 7 8
ON
OFF ON OFF ON
1 2 3 4 5 6 7 8
ON
ON OFF ON
1 2 3 4 5 6 7 8
ON
OFF OFF ON
1 2 3 4 5 6 7 8
ON
ON OFF ON
1 2 3 4 5 6 7 8
ON
ON
1 2 3 4 5 6 7 8
ESVK/KRV86 - ESVK/KRV88 Series - Installation handbook
ID
ON OFF OFF
ON OFF
ON ON OFF
10
11
ON 12
ON 13
ON 14
ON ON ON 15
on Fig. 2) accessible from the rear side of the module.
L
PROGRAMMING THE DOOR OPENING TIME
Switch
ON
1
1 2 3 4 5
ON
2
1 2 3 4 5
PROGRAMMING THE CONVERSATION TIME
3
Switch
ON
4
1 2 3 4 5
ON
5
1 2 3 4 5
6
PROGRAMMING THE ADDRESSING ORDER OF THE BUTTONS
Switch
7
ON
1 2 3 4 5
8
ON
1 2 3 4 5
9
PROGRAMMING THE MAIN CAMERA SELECTION
(ONLY ART. 4384 VERSIONS)
Switch
ON
1 2 3 4 5
ON
1 2 3 4 5
PROGRAMMING MODES (ONLY ART. 4384X VERSIONS)
Switch 8 sets the programming mode: "Standard" (switch in OFF
position) or "Advanced" (switch in ON position).
In "Standard" mode settings are made by switches from 1 to 7.
In "Advanced" mode all programming is made via the "VX2X00
Programmer" PC software connected to RS485 via an Art. 481 in-
terface. Please note that in this case the programming made by
switches from 1 to 7 wil be ignored.
Switch
ON
1 2 3 4 5
ON
1 2 3 4 5
- 11 -
Nr.5 Setting Up
OFF = 2 seconds
6 7 8
ON = 6 seconds
6 7 8
Nr.6 Setting Up
OFF = 1 minute
6 7 8
ON = 2 minutes
6 7 8
Nr.7
Button matrix Internal buttons
OFF = 1 - 40
6 7 8
ON = 41 - 80
6 7 8
Nr.8 Setting Up
OFF = Main camera internal
6 7 8
ON = Main camera external
6 7 8
Nr.8 Setting Up
OFF "Standard" programming mode
6 7 8
ON "Advanced" programming mode
6 7 8
66550045-EN - V6.2 - 31/10/20
Setting Up
= 1, 2
= 41, 42