Gree KW09HQ3D6D Series Service Manual page 23

2. FAN button
Press this button, Auto, Low, Medium-low, Medium, Medium-high, High speed can
speed is default. Under DRY
Note:
It's Low fan speed under Dry mode.
X-FAN function ： Hold fan speed button for 2s in COOL or DRY mode, the icon "
operation for a few minutes in order to dry
OFF is defaulted. X-FAN is not available in AUTO, FAN or HEAT mode.
This function indicates that moisture on e vaporator of indoor unit will be blowed after the unit is stopped to avoid mould.
Having set X- FAN function on: After turning off the unit by pressing ON/OFF
minutes. at low speed. In this period, Hold fan speed button for 2s to stop indoor fan directly.
Having set X- FAN function off: After turning off the unit by pressing ON/OFF button, the complete unit will be off directly.
3.MODE button
Press this button, Auto, Cool, Dry, Fan, Heat mode can be selected circularly. Auto
the initial value is 28 (82
Under other modes, the initial value is 25
(only for cooling and heating unit. As for cooling only unit, it won't have any action when it receives the signal of heating operation.)
4.+/- button
Press " + " or " - " button once increase or decrease set temperature 1°C(°F).
Holding " + " or " - " button, set temperature on remote controller will change
temperature indicator on indoor unit will change accordingly.
When setting TIMER ON, TIMER OFF or CLOCK, press " + " or " - " button to
buttons) When setting
TIMER ON, TIMER OFF or CLOCK, press " + " or " - " button to adjust time. (Refer to CLOCK, TIMER ON, TIMER
OFF buttons)
5.TURBO button
Under Cool or Heat mode, press this button can turn on or turn off the Turbo function.
After the Turbo function turned on, the signal of Turbo will display. The signal will
button
6.
Press this button to set left & right swing angle cycling as below:
7. button
5
Press this button to set swing angle, which circularly changes as below:
This remote controller is universal. If it receives threes kinds of following status, the
If guide louver is stopped when it is swinging up and down, it will remian its present position.
indicates guide louver swings back and forth in the five places, as shown in the figure.
7. CLOCK button
8
Press this button, the clock can be set up, signal
if continuously press this button for 2
During blinking, repress the Clock button or Confirm button, signal
After powered on, 12:00 is defaulted to
the current time value is Clock value, otherwise is Timer value.
9
9 .TIMER ON/TIMER OFF button
Timer On setting: Sign al "ON" will blink and display, signal
During 5 seconds blink, by
increased or decreased 1 minute. Hold pressing + or -
20
mode, Low fan speed only can be set up.
ATUO
the indoor unit even though you have turned off the unit. After energization, X-FAN
)
).
(77
OFF
OFF
blink and display. Within 5 seconds,
seconds above, in every 0.5 seconds, the value on ten place ofMinutewill be increased 1.
display and signal
pressing + or - button to adjust the time value of numerical section, every press of
button, 2 seconds later, it quickly change, the way of change is: During the initial
be circularly selected. After powered on, Auto fan
Low fan Medium-low fan
Medium-high fan
displayed and the indoor fan will continue
" is
button indoor fan will continue running for a few
mode is default while power on. Under Heat mode,
quickly . On releasing button after setting is finished,
adjust time. (Refer to CLOCK, TIMER ON, TIMER OFF
be automatically cancelled if changing the mode or fan speed.
swing angle will remain original.
the value can be adjusted by pressing + or - button,
will be constantly displayed and it denotes the setting succeeded.
will be displayed. If there is signal
erical section will become the timer on setting status.
will conceal, the num-
Medium fan
High fan
AUTO COOL DRY
FAN HEAT
be displayed that denotes
that button, the value will be
Technical Information
Service Manual