Gree KW09HQ3D6D Series Service Manual page 24

Service Manual
2.5 seconds, ten numbers change in the one place of minute, then the one place
and carry. During 5s blink, press the Timer button, the timer setting succeeds. The
at 2.5 seconds speed
the timer button, the Timer On will be canceled.
Before sett ing the Timer, please adjust the Clock to the current actual time.
One press this key to enter into TIMER OFF setup, in which case the TIMER OFF icon will blink. The method of setting is the sameas for
TIMER ON.
10.TEMP button
Press this button, you can see indoor set temperature, indoor ambient temperature
The setting on remote co-
When selecting " " with remote controller or no display, temperature indicator on
" " with remote controller,
selecting with remote controller, temperature indicator on indoor unit displays
outdoor ambient temperature. 3s later it will return to the setting temprature or it
button, every 200ms to send I FEEL once, after this function started,the remote control will send temperature to the main un it in every 10
minutes.When repress this button, this function will be turned off.
Attention: When displaying the outdoor ambient, the displaying range is 0-60
When it goes beyond the range, it keeps the threshold data (the smallest—0
Warm tips: When operating buttons on the cover please make sure the cover is closed completely.
Note: Outdoor temperature display is not available for some models. At that time,
indoor set temperature.
button
11. /
Press this button to achieve the on and off of healthy and scavenging functions in operation status. Press this button for the first time to start
scavenging function; LCD displays "
LCD displays " " and "
button for the fourth time to start healthy function; LCD display "
NOTE: This function is applicable to partial of models.
12.I FEEL button
Press this button once, to turn on the I FEEL function, then the figure of "I FEEL" will be displayed, after every press of other function button,
every 200ms to send I FEEL once, after this function started, the remote controller will send temperature
When repress this button , this function will be turned off. When I FEEL function is turned on, the remote controller should be put
area where indoor unit can receive the signal sent by the remote controller.
13.LIGHT button
Press this button at unit On or Off status, Light On and Light Off can be set up.
After powered on, Light On is defaulted.
14.WiFi button
WiFi
Press " " button to turn on or turn off WiFi function. When WiFi function is
controller; Under status
restore to factory default setting.
This function is only available for some models.
15.QUIET button
Press this button, the Quiet status is under the Auto Quiet mode (display "
singal) and Quiet OFF (there
Under the Quiet mode (Display "
The Quiet function is only available for some models.
16.SLEEP button
Press this button, can select Sleep 1 (
electrified, Sleep Cancel is de-
Sleep 1 is Sleep mode 1, in Cool modes: sleep status after run for one hour, the main unit setting temperature will increase 1
2 hours, setting temperature increased 2
one hour, the setting temperature will decrease 1
this setting temperature.
Technical Information
ntroller is selected circularly as below:
temperature indicator on indoor unit displays indoor ambient temperature; When
" . Press the button for the second time to start healthy and sc-
". Press this button for the third time to quit healthy and scavenging functions simultaneously. Press the
of remote controller off, press "MODE" and " WiFi " buttons simultaneously for 1s,
is no signal of " " displayed), after powered on, the Quiet OFF is defaulted.
" signal).
), Sleep 2 (
faulted.
, the unit will run at this setting temperature; In Heat mode:sleep
is constant, ten numbers change in the tens place of minute
or outdoor ambient temperature on indoor unit's display.
no display
indoor unit displays set temperature; When selecting
and the largest 60
indoor
" . Press this bu- tton again to repeat the operation above.
turned on, the " WiFi " icon will be displayed on remote
"
cancel the Sleep, circulate between these, after
), Sleep 3 ( ) and
, 2 hours, setting temperature will decrease 2
Timer On has been set up, repress
selecting "
outdoor ambient temperature. 3s later it will
depends on the other received signal within 3s.
).
unit receives " " signal, while it displays
avenging functions simultaneously;
to the main un it in every 10 minutes.
and "Auto" signal) and Quiet mode (display "
, then the unit will run at
" with remote
within the
WiFi module will
"
status after run for
21