Table of Contents
Advertisement
Advertisement
Chapters
Table of Contents
Related Manuals for Beckhoff C6017
Summary of Contents for Beckhoff C6017
- Page 1 Manual | EN C6017 Industrial PC 01/22/2021 | Version: 2.1...
-
Page 3: Table Of Contents
Grounding of the Industrial PC .................. 28 4.3.2 Connecting cables and power supply ................ 29 Switching the Industrial PC on and off..................... 30 5 Beckhoff Device Manager ........................ 31 6 Decommissioning............................ 34 Disconnecting the power supply and cables ................... 34 Disassembly and disposal ....................... 35 7 Maintenance ............................. 37... - Page 4 Table of contents 8 Troubleshooting ............................ 42 9 Technical data............................ 43 10 Appendix .............................. 44 10.1 Service and support......................... 44 10.2 Approvals............................ 45 Version: 2.1 C6017...
-
Page 5: Notes On The Documentation
Copyright © Beckhoff Automation GmbH & Co. KG. Publication of this document on websites other than ours is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. -
Page 6: For Your Safety
Exclusion of liability Beckhoff shall not be liable in the event of non-compliance with this documentation and thus the use of the devices outside the documented operating conditions. Description of safety symbols The following safety symbols are used in these operating instructions. -
Page 7: Fundamental Safety Instructions
• the operating instructions are in good condition and complete, and always available for reference at the location where the products are used. C6017 Version: 2.1... -
Page 8: Product Overview
Product overview Product overview The C6017 Industrial PC is part of the series of ultra-compact Industrial PCs for space-saving control cabinet installation. It is a high-performance device. This variant with further optional interfaces enables adaptation to specific applications and requirements. -
Page 9: Structure
Product overview Structure Fig. 1: C6017_Structure – basic configuration Table 1: Key - C6017 structure Component Description Mounting plate Plate for mounting the Industrial PC over the narrow sides in the control cabinet Status LEDs Status display for power, hard disk, TwinCAT... -
Page 10: Interface Description
The plug for the power supply is specified for 8 A and can accommodate cable cross-sections of up to 1.5 mm . The plug is included in the delivery. If you need a replacement connector, please contact your Beckhoff service team, quoting the order identifier C9900-P943 (see Chapter 10.1 Service and support). Version: 2.1 C6017... -
Page 11: Ethernet Rj45
Product overview 3.2.2 Ethernet RJ45 The C6017 has two Gigabit LAN ports (X102, X103). The Ethernet standards 100Base-T and 1000Base-T enable connection of corresponding network components with data rates of 100/1000 Mbit/s. The required speed is selected automatically. The RJ45 connection technology with twisted-pair cables is used. The maximum length of the cable connection is 100 m. -
Page 12: Usb
The Industrial PC has two USB interfaces (X105, X106). They are used to connect peripheral devices with USB interfaces. The following table shows the interface assignment based on the device generation: Table 5: USB interfaces based on device generation Generation USB interfaces C6017-0010 1x USB 2.0 (X105) 1x USB 3.0 (X106) C6017-0020 2x USB 3.0 (X105, X106) The two USB interfaces each supply up to 500 mA current and are electronically protected. -
Page 13: Displayport
The Industrial PC has a DisplayPort (X104) that enables connection of devices with DisplayPort. It facilitates transfer of image signals. In addition, DVI signals can be transferred via an adapter. Please order it from your Beckhoff sales team, quoting order identifier C9900-Z468 adapter cable DisplayPort to DVI, 40 cm. -
Page 14: Optional Interfaces
The Intel i210 (MAC/PHY) controller is used for both ports. The Ethernet ports are not switched. They are suitable for cycle times <= 1 ms and for distributed clock applications in EtherCAT. Fig. 7: C6017_Ethernet interface pin numbering Version: 2.1 C6017... -
Page 15: Rs232
Request to Send Signal in Clear to Send Signal in Ring Indicator Status LEDs The Industrial PC has three status LEDs: PWR, TC, HDD. They provide information on the following aspects: • the status of the power controller C6017 Version: 2.1... -
Page 16: Pwr Led
Bootloader is starting (start sequence is being run through) Magenta Flashing (0.5 s) S UPS capacitance test (if S UPS exists) Red/magenta Flashing Checksum error during the I2C transmission in the bootloader Cyan Flashing (2 s) contact Beckhoff Service Version: 2.1 C6017... -
Page 17: Hdd Led
The TC LED indicates the TwinCAT status. The colors and flashing intervals have the following meanings: Table 13: Meaning of the TC LED Color Flashing interval Meaning Green Steadily lit TwinCAT Run Mode Blue Steadily lit TwinCAT Config Mode Steadily lit TwinCAT Stop TwinCAT not started C6017 Version: 2.1... -
Page 18: Name Plate
The name plate provides information on the equipment fitted to the Industrial PC. xxxxxxxx xxxxxxxxxxxxx xxxxxxxxxxxxx xxxxxxxxxxxxx xxxxxxxxxxxxx Fig. 10: C6017 _Name plate example Table 14: Key - C6017 name plate Description Manufacturer, including address Model: The last four digits indicate the device generation Serial number (BTN) Date of manufacture... -
Page 19: 1-Second Ups
• Use only TwinCAT to control the 1-second UPS and save only persistent data with a maximum size of 1 The C6017 can optionally be ordered with internal uninterruptible power supply (UPS). This is a capacitive 1- second UPS for secure storage of persistent application data on the M.2 SSD. It requires TwinCAT and Windows Embedded Compact 7, Windows Embedded Standard 7 or Windows 10 IoT Enterprise. -
Page 20: Commissioning
4. Check the contents for visible shipping damage. 5. In case of discrepancies between the package contents and the order, or in case of transport damage, please inform Beckhoff Service (see Chapter 10.1 Service and support [} 44]). Version: 2.1 C6017... -
Page 21: Installation In The Control Cabinet
Commissioning Installation in the control cabinet The C6017 Industrial PC is designed for installation in control cabinets in machine and plant technology. Please observe the environmental conditions prescribed for the operation (see Chapter 9 Technical data [} 43]). Using different mounting plates, you can align the cable entry based on the application requirements. -
Page 22: Mounting Options
Fig. 14: • Connections point upwards (A) • Connections point downwards (B) • Connections point to the right (C) • Connections point to the left (D) Fig. 14: C6017 _Mounting options for mounting plate 2 Version: 2.1 C6017... -
Page 23: Fig. 15: Mounting Options For Mounting Plate 3
You have the following mounting options, which are shown in Fig. • Mounting via the rear of the device (A) • Mounting via the top of the device (B) • Mounting via the bottom of the device (C) Fig. 15: Mounting options for mounting plate 3 C6017 Version: 2.1... -
Page 24: Dimensions
Fig. 18 illustrates the dimensions using the mounting options via the rear of the device with mounting plate 3 with DIN rail adapter as an example. 65,9 81,9 32,3 47,3 Fig. 18: C6017 _Mounting plate DIN rail adapter Version: 2.1 C6017... -
Page 25: Installation In The Control Cabinet
After you have drilled the holes for the fastening screws in the control cabinet, you can mount the Industrial PC in the control cabinet with mounting plates 1 or 2. Fig. 19: C6017 _Mounting plates for control cabinet installation To install the Industrial PC in the control cabinet, follow the steps below: 1. -
Page 26: Fig. 20 C6017_Din Rail Adapter For Control Cabinet Installation
3. Keep the device pressed upwards and also hook the upper side of the adapter into the DIN rail (C). ð You have successfully installed the Industrial PC on the DIN rail. Fig. 21: C6017_DIN rail adapter mounted Version: 2.1 C6017... -
Page 27: Connecting The Industrial Pc
Set "PE" and "0 V" (24 V power supply) to the same potential (connected in the control cabinet). Connected devices that have their own power supply must have the same potential for "PE" and "GND" as the Industrial PC system (no potential difference). 230 V 24 V Grounding busbar Fig. 22: C6017 _Wiring example C6017 Version: 2.1... -
Page 28: Grounding Of The Industrial Pc
The EMC of the device is improved by functional earthing. You also establish the functional earthing by connecting the PE protective conductor connection to the central grounding point of the control cabinet panel in which the PC is installed. Version: 2.1 C6017... -
Page 29: Connecting Cables And Power Supply
3. Plug the power cable into the four-pin voltage connector of the Industrial PC. 4. Fasten the power cable to the power plug of the Industrial PC. 5. Connect the PC to your external 24 V power supply. 6. Switch on the 24 V power supply. C6017 Version: 2.1... -
Page 30: Switching The Industrial Pc On And Off
When you switch on the Industrial PC for the first time, the pre-installed operating system (optional) will be started. For any additional hardware you have connected, you have to install the drivers yourself afterwards. In addition, the Beckhoff Device Manager starts automatically. The Device Manager is a software from Beckhoff that supports you in configuring the PC. -
Page 31: Beckhoff Device Manager
• User name: Administrator • Password: 1 You also have the option of using the Beckhoff Device Manager to configure the Industrial PC remotely via a web browser. More detailed information is available in the Beckhoff Device Manager manual. First start Beckhoff Device Manager When your Industrial PC is booted for the first time, the Beckhoff Device Manager also starts automatically for the first time. -
Page 32: Fig. 24 Beckhoff Device Manager Home Page
To start the Beckhoff Device Manager manually, proceed as follows: 1. Open a web browser on the host PC. 2. Enter the IP address or the host name of the Industrial PC in the web browser to start the Beckhoff Device Manager. -
Page 33: Table 16 Password Generation
Beckhoff Device Manager Table 16: Password generation Procedure Example Start with one or two sentences. Complex passwords are more secure Remove the spaces. Complexpasswordsaremoresecure Abbreviate words or remove all vowels. Cmplxpsswrdsrmrscr Insert numbers and special characters to extend the Cmplxpsswrdsrmrscr#529954# password. -
Page 34: Decommissioning
To disconnect the cables from the Industrial PC, proceed as follows: 1. Make a note of the wiring configuration, if you wish to restore it with another device. 2. Disconnect all data transfer cables from the Industrial PC. 3. Finally, disconnect the grounding strap. Version: 2.1 C6017... -
Page 35: Disassembly And Disposal
3. Remove the PC from the control cabinet. ð You have successfully disassembled the PC. Fig. 25: C6017 _Position of the fastening screws Disassembly via DIN rail adapter To remove the Industrial PC from the control cabinet via mounting plate 3 with the DIN rail adapter, follow the steps below, which are shown in Fig. - Page 36 • Send plastic parts (polycarbonate, polyamide (PA6.6)) for plastics recycling. • Take metal parts to the metal recycling collection point. • Electronic parts such as fans and circuit boards must be disposed of in accordance with national electronic scrap regulations. Version: 2.1 C6017...
-
Page 37: Maintenance
Repair Only the manufacturer may repair the device. If a repair should be necessary, contact Beckhoff Service (see Chapter 10.1 Service and support). Cleaning... -
Page 38: Table 17 Replacement Recommendations For Pc Components
NOTE Use of incorrect spare parts The use of spare parts not ordered from Beckhoff Service can lead to unsafe and faulty operation. • Only use spare parts that you have ordered from Beckhoff Service. Beckhoff Industrial PCs are manufactured from components of the highest quality and robustness. They are selected and tested for best interoperability, long-term availability and reliable function under the specified environmental conditions. -
Page 39: Fig. 27 C6017 _Access To Battery And Storage Media
To do this, remove the two Torx TX6 screws and take off the cover (see Fig. 27). Fig. 27: C6017 _Access to battery and storage media You now have access to the battery (1) and storage medium (2) (see Fig. 28). -
Page 40: Replacing The Battery
It is used to supply power to the clock integrated on the motherboard. If the battery is depleted or missing, the date and time are displayed incorrectly. Replacement batteries should only be obtained from Beckhoff Service (see Chapter 10.1 Service and support). -
Page 41: Replacing The Storage Media
Data transfer before replacement If you want to exchange the SSD as recommended by Beckhoff, you must copy the data from the old to the new SSD. You can use the Beckhoff Service Tool (BST) for this purpose. The BST is a graphical backup and restore program for Industrial PCs with a Windows operating system. -
Page 42: Troubleshooting
Nothing happens after the Missing power supply of the Check the power supply cable Industrial PC has been switched on Industrial PC Call Beckhoff Service Other cause The Industrial PC does not boot Setup settings are incorrect Check the setup settings... -
Page 43: Technical Data
Technical data Technical data Table 20: Technical data Product designation C6017 Dimensions (W x H x D) 82 x 82 x 66 mm, without mounting plate Weight approx. 550 g without mounting plate approx. 610 g with mounting plate Supply voltage 20.4-30 V (24 V... -
Page 44: Appendix
Phone: + 49 (0) 5246/963-0 Fax: + 49 (0) 5246/963-198 E-mail: info@beckhoff.de The addresses of the worldwide Beckhoff branches and agencies can be found on our website at http:// www.beckhoff.com/. You will also find further documentation for Beckhoff components there. -
Page 45: Approvals
Appendix 10.2 Approvals The following table shows the certifications of the Industrial PC based on the device generation: Table 21: C6017 certifications Device generation Certifications C6017-0010 CE, EAC, UL C6017-0020 CE, EAC, UL FCC approvals for the United States of America... - Page 46 Fig. 12 C6017 _Mounting plates......................Fig. 13 C6017_Mounting options for mounting plate 1 ................Fig. 14 C6017 _Mounting options for mounting plate 2 ................Fig. 15 Mounting options for mounting plate 3..................Fig. 16 C6017 _Mounting plate narrow side ....................
- Page 47 Table 11 Meaning of the PWR LED......................Table 12 Meaning of the HDD LED ......................Table 13 Meaning of the TC LED ....................... Table 14 Key - C6017 name plate ......................Table 15 Mounting plate ordering options ....................Table 16 Password generation ........................
- Page 49 More Information: www.beckhoff.com/C6017/ Beckhoff Automation GmbH & Co. KG Hülshorstweg 20 33415 Verl Germany Phone: +49 5246 9630 info@beckhoff.com www.beckhoff.com...