Inserting Water System Filter; Assembling The Scrubbing Brush Head Body Brushes; Preparing To Work; Work - COMAC C85 ESSENTIAL Series Use And Maintenance Manual

Before using the machine for the first time the water system filter needs to be reset, for shipping reasons the filter cartridge and the cap have been
removed. To insert the filter cartridge in the water system filter body proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine is in a safe condition (see chapter
CAUTION: it is recommended to wear the appropriate PPE (Personal Protective Equipment) for the work to be carried out.
3. Close the tap output flow and turn the lever positioned near the operator seat in a clockwise direction (Fig.9).
4. Insert the filter cartridge in the housing on the cap (Fig.10).
N.B.: The O-ring gasket in the filter cartridge should be inserted into its seat in the cap.
5. Screw the cap onto the body of the detergent solution filter (Fig.4).
To fit the brush on the brush head body, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine is in a safe condition (see chapter
CAUTION: it is recommended to wear the appropriate PPE (Personal Protective Equipment) for the work to be carried out.
3. Go to the left-hand side of the machine and remove the left-hand splash guard, then move the fixing anchors on the brush head body into the
maintenance position (Fig.11).
4. With the brush head UP, insert the brush in the plate housing underneath the brush head, turning it until the three buttons engage with the niches
on the plate itself.
5. Turn in increments until the button is pushed towards the coupling spring and is locked in place (Fig.12).
N.B.: The image in Fig.12 indicates the direction of rotation for coupling the left brush; the right brush must be turned in the opposite direction.
Before beginning to work, it is necessary to:
1. Make sure the recovery tank is empty. If this is not the case, empty it (read
2. Check that the quantity of detergent solution in the solution tank is right for the type of work to be carried out. If necessary, fill the tank (for versions
without CDS, read
"FILLING THE SOLUTION
3. Check that the squeegee rubbers are in good working condition. If not, carry out maintenance (see
RUBBER BLADES").
4. Check that the splash guard rubber blades on the scrubbing brush head body are in good working condition. If this is not the case, replace them
(see "REPLACING THE SCRUBBING BRUSH HEAD BODY SPLASH
5. Check that the brushes are in good working condition. If this is not the case, replace them (see
BODY BRUSHES").
6. Check that the battery connector is connected to the machine's general system connector; if this is not the case, perform this operation.
1
ns Regulations Programs
1 2 3 Hour meter
50 12 10.000
Solution l Speed Km/h h

INSERTING WATER SYSTEM FILTER

ASSEMBLING THE SCRUBBING BRUSH HEAD BODY BRUSHES

"FILLING THE SOLUTION TANK" and
TANK" and "FILLING THE DETERGENT CANISTER (VERSIONS WITH
2
For Bright versions: Three working programs can be selected via the command display, the choice is based on the type of
work to be carried out and on the type of dirt to be cleaned, for example:
• Eco program: This program is ideal when performing cleaning primarily for maintenance purposes that does not require
any particular scrubbing power.
• Standard program: This program is recommended for regular cleaning operations on moderately dirty surfaces.
• Plus program: This program is useful when increased scrubbing power is required on resistant, stubborn dirt since it
increases the flow of detergent solution and pressure on the brushes to the maximum.
"MACHINE SAFETY MEASURES").
"MACHINE SAFETY MEASURES").

PREPARING TO WORK

"EMPTYING THE RECOVERY
"DETERGENT SOLUTION (VERSION WITHOUT
GUARD").

WORK

3 4
16
TANK").
CDS)"; for versions with CDS, read
CDS)").
"REPLACING THE SQUEEGEE BODY
"REPLACING THE SCRUBBING BRUSH HEAD
5 6