Nice Era Plus H Series Instructions And Warnings For Installation And Use page 8

5.8.2 - Memorising a second transmitter using "Mode II"
Caution! – This procedure memorises one key on the new transmitter using "Mode II", regardless of the Mode in which the key you press on the old transmitter is
memorised.
Before starting the procedure, bring the awning/shutter to a point half-way along its course.
01. (on the new transmitter) Press and keep pressing on the key to be combined with one of the available functions. Release the key after 8 seconds (in this case, the
motor does not perform any movement).
02. (on the old transmitter) Keep the n key pressed and wait for the motor to perform 4 movements. Upon completion, release the key.
03. (on the old transmitter) Briefly press the n key a certain number of times depending on the command you want to memorise:
– Step-by-Step command = 1 pulse
– Open > Stop > Open > Stop > command ... = 2 pulses
– Close > Stop > Close > Stop > command ... = 3 pulses
– Stop command = 4 pulses
After about 10 seconds, the motor performs a number of movements equal to the number of impulses given with the transmitter.
04. (on the new transmitter) Keep pressing the key to be combined with the chosen function and wait for the motor to perform 3 movements. Upon completion, release
the key. Caution! – If the motor performs 6 movements, it means that its memory is full.
01
New
03
Old
04
same
01
New
N.B. – When performing the procedure, you can cancel the memorisation at any time by keeping the n and s keys pressed simultaneously for 4 seconds Alternatively,
do not press any keys and wait 60 seconds for the motor to complete 6 movements.
01
Old
03
sec.
Old
5.9 - Total or partial deletion of memory
This procedure allows you to choose under point 05 the data that you want to delete.
5.9.1 - This procedure is done with a transmitter memorised using "Mode I"
Before starting the procedure, bring the awning/shutter to a point half-way along its course.
01. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02. Keep the s key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03. Keep the n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04. Keep the t key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
05. • To cancel the entire memory: keep the s and t keys pressed simultaneously and wait for the motor to perform 5 movements. Upon completion, release the
keys.
• To cancel the memorised transmitters only: do not press any keys and wait for the motor to perform 5 movements.
• To cancel just the parameters: keep the n key pressed and wait for the motor to perform 5 movements. Upon completion, release the key.
7 – Inglese
02
example
8
sec.
x 1 = Passo-passo
x 1 = Step-by-Step
x 2 = Apri > Stop > ...
x 2 = Open > Stop > ...
x 3 = Chiudi > Stop > ...
x 3 = Close > Stop > ...
0,5
sec.
x 4 = Stop
x 4 = Stop
5
3
sec.
––– Procedure 5.8.2 ––– executable only with a series transmitter Era P and Era W
PRG
6
2
sec.
x 1 = Passo-passo
x 1 = Step-by-Step
x 2 = Apri > Stop > ...
x 2 = Open > Stop > ...
x 3 = Chiudi > Stop > ...
x 3 = Close > Stop > ...
0,5
x 4 = Stop
x 4 = Stop
5
sec.
Old
10
?
sec.
02
PRG
...
2
04
1 /
2 /
3 /
10
?
sec.
4 /
4
1 /
2 /
3 /
4 /
PRG
6
2
sec.
New
example
5
sec.
New
PRG
3