Table of Contents
Advertisement
Quick Links
Introduction
This control system can be connected to a remote transmitter system to allow individual remote
control of the air bag system. The functions include individual corner up/down, all up/down,
front up/down, rear up/down, and timed dump all.
This control system can also be connected to a display module and pressure senders to allow
monitoring and control of all four corners and optional monitoring of the tank pressure. The
functions include four different height presets for automatic up/down control, manual up/down
control, and a pressure controlled bag dump. The bag senders can be either 150 psi units or
400 psi units for high pressure systems. The tank sender is always the 400 psi unit.
IMPORTANT: Make sure to always disconnect the negative cable from the battery if you are
going to be working on or under the vehicle. Failure to do so can result in serious injury if the
system is accidentally activated.
Wiring
Main connector
RED
BLACK
YELLOW
WHITE/GREEN
GREEN
WHITE/PURPLE
PURPLE
WHTE/ORANGE
ORANGE
WHITE/BROWN
BROWN
Display/sender connector
GREEN
PURPLE
ORANGE
BROWN
GRAY
GRAY CABLE, RED
GRAY CABLE, BLACK
GRAY CABLE, bare wire to display GND terminal (cable shield)
GRAY CABLE, WHITE
GRAY CABLE, GREEN
BLUE
Remote receiver connector
Mates to ARR-1000 module harness connector
ARC-1000 rev. A
Air Bag Control System
constant 12V power
ground
accessory power
right rear down solenoid (not used for FRONT/REAR setup)
right rear up solenoid (not used for FRONT/REAR setup)
left rear down solenoid
left rear up solenoid
right front down solenoid (not used for FRONT/REAR setup)
right front up solenoid (not used for FRONT/REAR setup)
left front down solenoid
left front up solenoid
right rear pressure sender (not used for FRONT/REAR setup)
left rear pressure sender
right front pressure sender (not used for FRONT/REAR setup)
left front pressure sender (front sender for FRONT/REAR setup)
tank pressure sender
to display PWR terminal
to display GND terminal
to display WHT terminal
to display GRN terminal
external remote input
(rear sender for FRONT/REAR setup)
1
Advertisement
Table of Contents
Related Manuals for Dakota Digital ARC-1000
Summary of Contents for Dakota Digital ARC-1000
- Page 1 ARC-1000 rev. A Air Bag Control System Introduction This control system can be connected to a remote transmitter system to allow individual remote control of the air bag system. The functions include individual corner up/down, all up/down, front up/down, rear up/down, and timed dump all.
- Page 2 OPERATION AS REMOTE CONTROL SYSTEM The remote system is active when the large red power wire has power and the accessory power wire does not. This prevents accidental operation using the remote system while the vehicle is being driven. When the remote system is ready and waiting to operate the green light by the programming switches will be flashing slowly.
- Page 3 Front Up/Down All Up Bag Dump All Down Rear Up/Down OPERATION FOR MODE 2, DIP switch #2 ON The key chain transmitter has four buttons. They are referred to below as button 1, 2, 3, and 4. Buttons 1 and 2 are on the top, to the right and left of the green light. Buttons 3 and 4 are below them.
-
Page 4: Programming Switches
PROGRAMMING SWITCHES There are four programming switches located next to the main harness connector. They are used to set up the operation of the remote system. Switch #1 Select sender type (not used for remote system) Switch #2 Select operation mode. Switch #3 Select bag dump time. -
Page 5: Troubleshooting Guide
TROUBLE SHOOTING GUIDE IMPORTANT: Make sure to always disconnect the negative cable from the battery if you are going to be working on or under the vehicle. Failure to do so can result in serious injury if the system is accidentally activated. Symptom Possible Problem Solution... -
Page 6: Manual Control
OPERATION AS AUTO HEIGHT CONTROL SYSTEM The auto height control system is active when both the large red power wire and the accessory power wire are on. When the accessory power is off the display and height control will shut down to prevent draining the battery down. - Page 7 Auto select: Press one of the corner buttons to select the auto height mode you want. Press the mode select button to go on to the bag dump or auto program screens. Bag Dump: Press the top right and bottom right switches at the same time to start the bag dump. Press the mode select switch to go on to the auto program or auto/manual screens.
-
Page 8: Auto Program
This system can be used with 2 senders (front/rear), 3 senders (front/rear & tank), 4 senders (4 corners), or 5 senders (4 corners & tank). The bag senders can be either Dakota Digital SEN- 03-1, 150 psi senders or Dakota Digital SEN-03-5, 400 psi senders. The tank sender is always a SEN-03-5, 400 psi sender. - Page 9 To enter the setup mode to make adjustments to these values, press and hold the left, center switch while you are turning the key on. The display will show the Dakota Digital startup message. Release the switch. The settings will be displayed as shown below.
-
Page 10: Display Mounting
PROGRAMMING SWITCHES There are four programming switches located next to the main harness connector. They are used to set up the operation of the remote system. Switch #1 Select sender type Switch #2 Select operation mode. (not used for control system) Switch #3 Select bag dump time. - Page 11 Return gauge for repair. (contact factory) Switches will not operate 10A fuse is blown. Replace fuse. any of the solenoids. 4510 W. 61ST St. N., Sioux Falls, SD 57107 Phone: (605) 332-6513 FAX: (605) 339-4106 www.dakotadigital.com dakotasupport@dakotadigital.com ©Copyright 2004 Dakota Digital Inc.