Related Manuals for Vanco HDWIRKIT
Summary of Contents for Vanco HDWIRKIT
- Page 1 HDMI® WIRELESS EXTENDER/ RECEIVER Vanco Part Number: HDWIRKIT HDWIR-RX Technical Support www.vanco1.com • techsupport@vanco1.com • 800-626-6445...
-
Page 2: Dear Customer
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. - Page 3 Receiver do not require line of site transmission, the wireless signal will travel through most obstacles with no issues. Out of the box, the HDWIRKIT works as a point to point configuration, however also supports having multiple sets on the same site (up to 10) and one to multiple (1 TX to up to 4 RX) displays using HDWIR-RX receivers (sold separately).
-
Page 4: Specifications
PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: • Wireless Transmitter (HDWIRKIT only) • Wireless Receiver • 5V/2A Power Supply • IR Blaster (TX) •... -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS TRANSMITTER 1. Antennas 2. RF Channels (Selectable 0-9 to “marry” to Receiving unit; or to split to multiple HDWIR-RX receivers) 3. Channel Toggle Switch (will change RF Channels 0-9 sequentially) 4. IR Sensor (for included remote to change to RF channels remotely) 5. - Page 6 PANEL DESCRIPTIONS RECEIVER 1. Antennas 2. RF Channels (Selectable 0-9 to “marry” to Transmitting unit; other Receivers can be set to the same RF channel to split signal) 3. Channel Toggle Switch (will change RF Channels 0-9 sequentially) 4. IR Sensor (for included remote to change to RF channels remotely) 5.
-
Page 7: Connect And Operate
CONNECT AND OPERATE Connect HDMI cable from a source into the HDMI IN port of the TRANSMITTER OPTIONAL: Connect the provided IR BLASTER into the IR OUT port of the TRANSMITTER OPTIONAL: Connect HDMI Cable to the HDMI OUT port to loop-out to a local display such as a control room display Connect an HDMI cable from the HDMI OUT port of the RECEIVER to a display or sink device OPTIONAL: Connect the provided IR RECEIVER into the IR IN port of the RECEIVER... -
Page 8: Ir Pass-Through
IR PASS-THROUGH The IR system allows you to control the source that is connected to the extender unit, from the display. There are two important things to note when setting up the IR system: The IR Receiver (IR RX) is always what you point your remote at to send an IR signal. This pigtail is placed at the display for controlling the source. - Page 9 IR RECEIVER (RX) IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR IN port of RECEIVER; place receiver at or near display. • Note: Due to possible differences in 3rd party IR cables, please use the IR cables that came with the product.
-
Page 10: Troubleshooting
Look to remove other wireless signal that may be disrupting the transmission SAFETY AND NOTICE The HDWIRKIT/HDWIR-RX has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the HDWIRKIT/HDWIR-RX should be used with care. -
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 Vanco® International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...