Maintenance And Storage - MSA Workman Instructions For Use Manual

of the housing. Never drop the unit from any height. Always set it down carefully. When in use,
protect the line from contacting sharp corners and edges. Prevent loops from forming in a slack
line and being pulled tight, causing line kinking. Do not allow foreign matter to enter the housing.
Do not permit the line to snag or be crushed. Do not use where objects may fall or otherwise
interfere with the operation or ability of this device to function properly. It is essential for safety that
the equipment is withdrawn from use immediately if any doubt arise about its condition for safe
use. A record must be kept by the user. Refer to labels for the material of the retractable lanyard.
After a rescue operation the product must be inspected by a competent person. When attaching
the product, choose an anchor point directly ABOVE the user's position to minimize swing falls
(see figure 15d). Avoid any point on which strength is doubtful. Potential for falls and fall distance
MUST be minimized. Consideration MUST be given to the necessary minimum clearance (see
figure 16) below the feet of the user to prevent a collision with the structure or the ground. The
minimum recommended clearance is 3 m. If the product has been subjected to fall arrest or impact
forces, it MUST be immediately removed from use and tagged "UNUSABLE". Remove unit from
service if the load indicator (see figure 1 a) is deployed. Do not leave a product's line extended
when it's not being used for fall protection. Do not expose the line to sharp edges, abrasive
surfaces, sparks, flame, or heat above 60
exposure to fall hazards. A separate independent fall arrest system may be required. It is essential
for the safety of the user that if the product is re-sold outside the original country of destination
the reseller shall provide instructions and additional relevant information for use, for maintenance,
for periodic examination and for repair in the language of the country in which the product is to be
used. Failure to follow these warnings or misuse can cause serious personal injuries or death.
Strictly adhere to the cleaning instructions in this section to prevent adverse effects on the
materials used in the RTFA-R .Clean the RTFA-R periodically with a clean damp (not wet) cloth to
remove dirt or contamination which may cause corrosion, hamper operation, or diminish readability
of the labels. To remove oil or grease, use a mild laundry detergent. Do not use chemicals,
harsh detergents, abrasives, or pressure washers. Never immerse the RTFA-R in water or other
liquid. Excessive accumulation of dirt, paint or other foreign matter may prevent proper function
of the RTFA-R, and, in severe cases, weaken the line. Contact MSA with questions concerning
product conditions and cleaning. Some environments may require the RTFA-R be disinfected.
Contact MSA for aid in determining the proper disinfection procedure for the specific application.
Tag damaged equipment or equipment needing maintenance as "UNUSABLE" and remove from
service. Repair and maintenance (other than cleaning) must be performed by an MSA authorized
service center. Moving parts of snaphooks and carabiners may require periodic lubrication with low
viscosity penetrating oil. Follow lubricant manufacturer's instructions. Do not over-lubricate. Wipe
excess with a clean, dry cloth. Transport the product in a package to protect it from cuts, moisture,
chemicals and their vapours, extreme temperatures, and ultraviolet rays. Protect the line at the
nozzle during transportation to prevent damage. Secure the RTFA-R housing and snaphook from
movement when possible. Store the RTFA-R in a cool, dry and clean place out of direct sunlight.
Avoid areas where heat, moisture, light, oil, and chemicals or their vapors or other degrading
elements may be present. Never allow RTFA-R to rest for lengthy periods of time on concrete or
ash floors as lime sulfur and ash can cause corrosion. Store the RTFA-R with line fully retracted.
Equipment which is damaged or in need of maintenance should not be stored in the same area as
usable equipment. Heavily soiled, wet, or otherwise contaminated equipment should be properly
maintained (e.g. dried and cleaned) prior to storage. Prior to using equipment which has been
stored for long periods of time, a Formal Inspection should be performed by a competent person.
Only store the RTFA with the cable fully retracted and with the rubber cable bumper seated into the nozzle to protect
the cable against permanent bends
© 2015 MSA
° C. When installing or removing the product, limit
MAINTENANCE AND STORAGE
Caution
!
P/N 10171660
21