Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CHERUBINI Skipper Senso
Summary of Contents for CHERUBINI Skipper Senso
-
Page 3: Table Of Contents
Table of contents: INTRODUCTION .......................p. 26 Warnings .........................p. 26 Guarantee / EU Declaration of conformity ...............p. 26 Remote control - legend ..................p. 27 Arrow keys - legend ....................p. 27 Insertion/replacement of batteries ................p. 27 Symbols - legend .....................p. 28 Keyboard .........................p. 28 PRELIMINARY OPERATIONS ..................p. -
Page 4: Introduction
Failure to comply with these instructions annuls CHERUBINI’s responsibilities and guarantee. EU DECLARATION OF CONFORMITY CHERUBINI S.p.A. declares that the product is in conformity with the relevant Union harmonisation legislation: Directive 2014/53/EU, Directive 2011/65/EU. The full text of the EU declaration of conformity is available upon request at the... -
Page 5: Remote Control - Legend
REMOTE CONTROL - LEGEND RGB 1.8” LCD display, 128x160 pixel Arrow keys Middle key ARROW KEYS - LEGEND - UP BACK FORWARD - STOP/ - DOWN SELECT INSERTION/REPLACEMENT OF BATTERIES SKIPPER Senso works with two 1,5V Alkaline batteries (AAA) format LR03. To replace batteries, only use equally good types. -
Page 6: Symbols - Legend
SYMBOLS - LEGEND Tilting blind Blind Battery Sceen Venetian blind Aerial Awning KEYBOARD Back key Capital letters small letters special characters Numbers and symbols Enter key Space key Use the arrow keys to move inside the keyboard and confirm the required letter by pressing the middle key (SELECT). -
Page 7: Preliminary Operations
PRELIMINARY OPERATIONS These operations are only necessary the first time you switch on your remote control. All setups can be modified at any time by accessing the SETTINGS section. 1 - Follow the instructions on page 27 to insert the batteries. The screen of the remote control will be activated immediately. -
Page 8: System Status Legend
SYSTEM STATUS LEGEND Remote System Command control time transmission battery level indicator Mar 15:22 Screen name SYSTEM STATUS Automation operational Active Automatic timetable operational (if enabled) 08:00/17:00 mode Brightness: 0135 Last command Season option active Temperature: 20 °C Temporarily disable sent Summer automatic operation... -
Page 9: Operational Modes
OPERATIONAL MODES Each time the display is activated, the currently set operational mode is indicated on the SYSTEM STATUS screen. Two operational modes are available: - Manual - Automatic When the remote control is turned on for the first time it is set to manual mode. Setting the Operational Mode To change the Operational Mode, perform the following steps from the Main Menu: A and C buttons: to go... - Page 10 Automatic 08:00/17:00 Twilight threshold Brightness: 0135 Brightness bar Brightness hysteresis frame Temperature: 20 °C Temperature Temperature bar intervention threshold Thresh./Main menu BRIGHTNESS: Quick start Brightness level Motor command Effect Above the hysteresis frame DOWN Less light Below the hysteresis frame More light Within the hysteresis frame No command or STOP (if in...
-
Page 11: Automatic Timetable" Function
AUTOMATIC TIMETABLE function (option to be enabled) Enabling this function the system works in AUTOMATIC mode only within the timetable set by the user (factory settings: 8 – 20). - When the timetable is started the automation enables management of the brightness. - When the timetable expires, and when the light falls below the twilight threshold, the device is given the command to close completely (DOWN if blinds/ venetian blind, UP if awning). -
Page 12: Programming For Daily Use
PROGRAMMING FOR DAILY USE Enable the sensors: Both sensors are factory enabled. To disable or enable the brightness or temperature sensors, take the following steps from the Main Menu: A and C buttons: to go from Mar 15:22 Mar 15:22 Mar 15:22 one function list to the next MAIN... -
Page 13: Season Option Settings
Season Option Settings: Season Option is managed by the temperature sensor. To set the season desired, do the following: A and C buttons: to go from Mar 15:22 Mar 15:22 Mar 15:22 one function list to the next MAIN PROGRAMMING SEASON OPTION B button: to enable/disable Mode... -
Page 14: Setting The "Automatic Disable" Time
In this screen the remote control reacts immediately to the sensor threshold steps. It is therefore possible to check if the Skipper Senso is properly communicating with the motor it is connected to. To perform the test, go to the “Sensors Test” item on the display and directly change the threshold values. -
Page 15: Settings
SETTINGS This section will allow you to change both the basic setups of the remote control (language, day, time) and the values which have been pre-set in the factory. ATTENTION! When you replace flat batteries, all the settings and the programming carried out until the time of replacement will be held in the remote control memory. -
Page 16: Program Lock
4 seconds in order to make this section accessible. DEVICE The Skipper Senso is able to manage a device such as a blind/screen, awning, tilting blind or venetian blind that will already be created at the moment it is turned on. To enable the sensor function, it is necessary to memorise the motor on the remote control with one of the procedures illustrated below. -
Page 17: Storing Of The First Remote Control
The Skipper LCD and Skipper Senso have the same remote control memorisation procedure. For this reason, in the following pages, we will refer to a generic “LCD remote control” without specifying whether it is a Skipper Senso or an LCD. - Page 18 Before proceeding make sure that the motor/receiver is powered. 1 To execute the ADD FROM function rocedure 1- Already stored remote control: a. Position yourself on the desired channel and carry out the following sequence: 2- LCD remote control to be stored: a.
- Page 19 Giro Series LCD remote control (not-LCD) On Skipper Senso: perform the button sequencing from the “System Status” screen. On Skipper LCD: select the device on which you wish to proceed. STORING OF THE FIRST REMOTE CONTROL ATTENTION! This Programming is only necessary when the motor or receiver is installed for the first time, that is to say, when it is not yet connected to any remote control.
- Page 20 - On Skipper Senso go to the “System Status” screen. - On the Multi-channel remote controls (Skipper series or Giro series) position yourself on the desired channel. 4To add an LCD remote control to a device created with another Cherubini rocedure remote control:...
-
Page 21: Modify A Device
To save the changes: SAVE. DELETE A DEVICE If a new device is to be memorised on Skipper Senso, it is necessary to first proceed with the deletion of the current device. Proceed as follows: Main / Programming / Device / Delete / DELETE When requested, verify successful deletion with the UP/DOWN/STOP buttons. -
Page 22: Information For The Installer
Tilting blind in tilt area: UP = less light; DOWN = more light DEVICE: any motor linked with the Skipper Senso remote control. Each device is linked with a name which can be customized by the customer (e.g. kitchen, bedroom, terrace) and with a type (blind, awning, etc.) which clearly indicate which element of the house... -
Page 23: Technical Features
TYPE OF DEVICE/GROUP: - AWNING: type of device referring to sun protection awnings outside the house. - BLIND: type of device referring to the blinds of the house. - TILTING BLIND: motor installed on tilting blade blinds. - VENETIAN BLIND: motor installed on the venetians blinds. TECHNICAL FEATURES Number of channels Consumption during operation... - Page 24 CHERUBINI S.p.A. Via Adige 55 25081 Bedizzole (BS) - Italy Tel. +39 030 6872.039 | Fax +39 030 6872.040 info@cherubini.it | www.cherubini.it CHERUBINI Iberia S.L. Avda. Unión Europea 11-H Apdo. 283 - P. I. El Castillo 03630 Sax Alicante - Spain Tel.