Parameter - BONFIGLIOLI Vectron ACTIVE CUBE Applications Manual

Voorhout • Groningen • Weert • Hoogerheide
8

Parameter

The parameter is available in the four data sets.
No. Description
Local/Remote
412
Frequency Switch-off Limit
417
PID-Controller Enable
800
Source Reference Value
801
Source Actual Value
802
Kp
803
Tn
804
Tv
805
Negative Limit Controller Output
806
Positive Limit Controller Output
807
Invert Controller Output
809
Ramp Increment
810
Enable Ramping
811
Limit Ramp-Switch-Off
812
Limit Ramp-Switch-On
813
Adapt Output by Diameter
815
Activate el. Gear
830
Source Frequency Setpoint
831
Gear Factor Numerator at Dmin
832
Gear Factor Denominator at
833
Dmin
Source Gear Factor Percentage
834
Value
Offset Frequency
835
Activate Frequency Offset
836
Activate Torque Limitation
860
Torque at Dmax
861
Source Diameter dependent Fac-
862
tor
Static Friction Compensation
865
Dynamic Friction Compensation
866
Minimum Deviation for Comp.
869
Acceleration
Mech. Time Constant at Dmin
870
Mech. Time Constant at Dmax
871
Current Limit for Compensation
872
Mode Diameter Calculator
880
11/13
T
+31(0)88 7865800
Parameter
Setting range
Unit
- Local-Remote table
Hz 0.00 .. 999.99
- Sources logic table
Source percentage
-
table
Source percentage
-
table
- -100.00 .. 100.00
ms 0 .. 600000
ms 0 .. 600000
Hz -999.99 .. 0.00
Hz 0.00 .. 999.99
Hz Sources logic table
Hz/s 0.01 .. 999.99
- Sources logic table
% 0.00 .. 100.00
% 0.00 .. 100.00
- Sources logic table
- Sources logic table
Source-frequency
-
table
-2147483647 ..
-
2147483647
- 1 .. 2147483647
Source percentage
-
table
Hz -50.00 .. 50.00
- Sources logic table
- Sources logic table
% 0.00 .. 300.00
Source percentage
-
table
% 0.00 .. 30.00
%/
0.00 .. 30.00
Hz
Hz 0.00 .. 999.99
ms 0 .. 60000
ms 0 .. 60000
A 0.0 .. 12.0
- 0, 1, 10
ACU
Winding Drive
I elsto.eu
Chap-
Default set-
ter
tings
44 – Ctrl.
Cont.+KP, Dir. 3.3
Cont.+KP
999.99 5.5
7 - Off 5.1.1
9 – Zero 5.1.1
9 - zero 5.1.1
1.00 5.1.1
250 5.1.1
0 5.1.1
-30.00 5.1.2
30.00 5.1.2
7 - Off 5.1.4
15.00 5.1.2
Sources logic
5.1.2
table
8.00 5.1.2
10.00 5.1.2
7 - Off 5.1.4
7 - Off 5.3.1
9 - zero 5.3.1
1 5.3.1
1 5.3.1
8942 – Speed
Factor at Dact 5.3.1
filtered
0.00 5.3.1
7 - Off 5.3.1
7 - Off 5.4
100.00 5.4
8944 – Torque
Factor at Dact 5.4
filtered
0.00 5.5.1.1
0.00 0
1.00 5.5.2.3
0 5.5.2.1
0 5.5.2.2
2.8 0
0 - Off 5.2
41