Husqvarna Automower 305 Workshop Manual page 11

LCD temperature : Measured by a temperature
•
sensor on the main circuit board.
4.4.1.5 Tools - Info -
The menu shows:
• COM : the version of the program on the
communication circuit board.
SIM card :
•
OK : Connected.
•
PIN : SIM PIN is required.
•
PUK : SIM PUK is required. To enter the PUK
•
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
Locked : The SIM card is locked. The SIM card
•
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
Error : Other fault.
•
- : Automower ®
• Connect is not active or no SIM
card is inserted.
GPRS :
•
• Ok : The communication status with the app.
Note: The communication status must be
there is no communication with the app.
Error : Not connected, no GRPS link.
•
Search : Not connected, GPRS link ok.
•
• Blocked : The communication circuit board is
blocked. The serial number of the
communication circuit board is not registered on
Husqvarna server. Replace the communication
circuit board.
SIMs : Data is not transmitted. Automower
•
Connect is attempting to transmit data but the
Husqvarna server is not receiving.
Note: If the SIM card is a cash SIM card and
there is no money left, this can cause the
code.
PIN : SIM PIN is required.
•
PUK : SIM PUK is required. To enter the PUK
•
code, insert the SIM card into a cell phone.
Note: You have to enter the PUK code when an
incorrect PIN code is entered too many times.
You can not enter the PUK code in the product.
Locked : The SIM card is locked. The SIM card
•
is permanently locked and must be replaced.
Note: The SIM card is locked when an incorrect
PUK code is entered too many times.
1414 - 001 -
Error : Other fault.
•
- : Automower
•
card is inserted.
Data : Data transmission On/Off .
•
• SMS : SMS function On/Off .
RSSI : The signal strength of GPRS reception,
•
between 0-98. A higher the value means a better
reception. The value must be more than 10 for a
stable connection.
Carrier : The name of the operator.
•
APN : The APN used for the operator.
•
APN user : User name for APN.
•
• APN pwd : Password for APN.
Geofence : GPS coordinates for the center point for
•
the geofence
GPS signal : The strength of the GPS reception. In
•
order to set the center position of the Geofence, the
GPS signal must be
4.4.1.6 Tools - Info - Motors
Tools - Info - Motors menu has these sections:
The
Wheel motor
•
Cutting motor
•
Info - Motors - Wheel motor menu shows:
The
Speed for the left/right wheel motor.
•
Current (mA) for the left/right wheel motor.
•
Power (%) for the left/right wheel motor.
•
Ok or
Info - Motors - Cutting motor menu shows:
The
Speed of the cutting motor.
•
Current (mA) for the cutting motor.
•
• Average current (mA) for the cutting motor.
4.4.2 Tools - History, total
4.4.2.1 Tools - History, total - Key data
The Tools - History, total - Key data menu shows:
®
Total running : The total time in hours that the wheel
•
motors have been running.
Total running also includes the time when the
Note:
SIMs
product is running without mowing.
Total mowing : The total time in hours that the blade
•
motor has been running.
Total search time : The total time in hours that the
•
product has been in search mode. This means the
time from starting to search for the charging station,
until the product has docked. Depending on the
installation and work area, it is normal with 10-20%
search time of the total running time.
Total charge time : The total time in hours when the
•
product has been charging.
Complete chargings : The total number of complete
•
chargings. A complete charging is defined as a
charging that proceeds for more than 20 minutes,
and is terminated when the charge current is less
than 300 mA.
®
Connect is not active or no SIM
Strong .
Special menus - 11