Husqvarna Automower 305 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Lawn Mower
  5. Automower 305
  6. Operator's manual

Husqvarna Automower 305 Operator's Manual

Robotic lawn mower
Hide thumbs Also See for Automower 305:
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's manual
®
HUSQVARNA AUTOMOWER
305/310 Mark II/315 Mark II
EN, English
Read the operator's manual carefully and make sure that you
understand the instructions before you use the product.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna Automower 305

Summary of Contents for Husqvarna Automower 305

  • Page 1 Operator's manual ® HUSQVARNA AUTOMOWER 305/310 Mark II/315 Mark II EN, English Read the operator's manual carefully and make sure that you understand the instructions before you use the product.

  • Page 2: Table Of Contents

    Contents 6.3 Replacement of the blades......... 35 1 Safety 6.4 Battery..............36 1.1 Safety definitions...........3 6.5 Winter service............. 36 1.2 General safety instructions........3 7 Troubleshooting 1.3 Safety instructions for installation......4 1.4 Safety instructions for operation......4 7.1 Introduction - troubleshooting......37 1.5 Safety instructions for maintenance...... 4 7.2 Fault messages...........37 1.6 Battery safety............

  • Page 3: Safety

    • If there is a risk of thunderstorm, Husqvarna or mental capabilities or lack of experience and recommends that the power supply and all the knowledge, if they have been given supervision...

  • Page 4: Safety Instructions For Installation

    33 . Husqvarna recommends to set the • The product must only be operated, maintained and repaired by persons that are fully conversant product to operate when the work area has no with its special characteristics and safety activity.

  • Page 5: How To Lift And Move The Product

    1.7 How to lift and move the product WARNING: The product must be switched off before lifting it. The product is disabled when the indicator lamp on the keypad is not lit. CAUTION: Do not lift the product when it is parked in the charging station. It can damage the charging station and/or the product.

  • Page 6: Introduction

    The serial number and the product number are on the product rating plate and on the product carton. • Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register your product.

  • Page 7: Product Overview

    2.2 Product overview Product body 16. Cutting height adjustment Top cover 17. Maintenance tool Hatch to keypad, display and cutting height 18. Cutting system adjustment 19. Chassis box with electronics, battery and motors Stop button 20. Handle Rear wheels 21. Loop wire for boundary wire and guide wire Front wheels 22.

  • Page 8: Symbols On The Product

    31. Alarm decal The chassis contains components which are sensitive to electrostatic discharge 2.3 Symbols on the product (ESD). The chassis must also be resealed in a professional manner. For these These symbols can be found on the product. Study them reasons the chassis shall only be opened carefully.

  • Page 9: Symbols On The Battery

    The schedule is set for the product to not cut the grass. Read the user instructions. Do not discard the battery into fire and do The product overrides the schedule. not expose the battery to a heat source. The battery indicator shows the charge level of the battery.

  • Page 10: Menu Structure Overview - 1

    2.7 Menu structure overview - 1 Schedule Overview/Monday Period 1 Period 2 Copy Reset Current All week days Security Advanced Security level New loop Change Duration Medium High signal PIN code Duration Duration of alarm of time lock Messages Fault Info messages messages...

  • Page 11: Menu Structure Overview - 2

    2.8 Menu structure overview - 2 Installation Lawn Find charging station Advanced coverage Guide Boundary Charger Area 1-3 Charging station range Delay Delay Disable More Disable More time time Test Reset Test Test Reset guide right left How? Disable More Corridor Exit Reversing...

  • Page 12: Display

    2.9 Display The display on the product shows information and settings of the product. To access the display, push the STOP button. 2.10 Keypad Use the keypad on the product to move around in the menu structure. To get access to the keypad, push the STOP button.

  • Page 13: Installation

    The sound level decreases after some time. Note: Refer to www.husqvarna.com for more 3.4 Before the installation of the wires information about installation. You can select to attach the wires with stakes or bury 3.2 Main components for installation...
  • Page 14 3.4.3 To examine where to put the • Put the charging station in an area with protection from the sun. boundary wire • If the charging station is installed on an island, make sure to connect the guide wire to the island. CAUTION: There must be a barrier of To make an island on page 16 .
  • Page 15 " 10 cm / 4 " max 1 cm / 0.4 • If you have a paving stone path that is in level with the lawn, put the boundary wire below the paving stone. Note: If the paving stone is minimum 30 cm / 12 Drive Past in.
  • Page 16 • For slopes adjacent to a public road, put a barrier Isolate or remove obstacles that slope of minimum 15 cm / 6 in. along the outer edge of slightly, for example, stones, trees or roots. the slope. You can use a wall or a fence as a This will prevent damage to the blades of the barrier.
  • Page 17 • Put the boundary wire around the secondary area 3.4.5 Work area examples To make an island (B) to make an island. Refer to on page 16 . • If the charging station is put in a small area (A), make sure that the distance to the boundary wire Note: The boundary wire must be put as 1 loop...

  • Page 18: Installation Of The Product

    Read and understand the instructions about where To examine to put the charging station. Refer to where to put the charging station on page 13 . Put the charging station in the selected area. Note: Do not attach the charging station with the screws to the ground until the guide wire is To install the guide wire on page installed.

  • Page 19: To Put The Wire Into Position With Stakes

    Open the connector and put the boundary wire in the connector. Close the connector with a pair of pliers. Put the 2 ends of the boundary wire and the end of the guide wire into the coupler. Note: Make sure that you can see the ends of the wires through the transparent area of the coupler.

  • Page 20: To Bury The Boundary Wire Or The Guide Wire

    CAUTION: Cutting the grass too low right after installation can damage the wire insulation. Damage to the insulation may not cause disruptions until several weeks or months later. Put the boundary wire and the guide wire on the ground. Put the stakes at a maximum of 75 cm / 30 in. distance from each other.
  • Page 21 Note: Make a note of the PIN code. Refer to Introduction on page 6 . 3.9.3 Calibration The calibration process is automatic. After the basic settings are done, the product moves away from the charging station and stops, while it calibrates some of the product settings.

  • Page 22: Product Settings

    The functions of the product hours to validate your account. have factory settings that are applicable for almost all Log in to your Husqvarna account in the work areas, but the settings can be adapted to the ®...
  • Page 23 Use the arrow buttons and the OK button to move Note: The lawn should not be cut too often to obtain Schedule > Overview > through the menu structure the best result. If the product is allowed to operate too Copy .
  • Page 24 4.2.4.1 To set the security level Use the arrow buttons and the OK button to move Security > Advanced > through the menu structure Select 1 of 3 security levels for your product. Duration > Duration of time lock . To get access to the menu in the Do steps 1–3 in Use the number buttons to select a time interval of...
  • Page 25 Systematic Passage Mowing function is suitable 4.2.6.1 To set the Weather Timer to mow narrow passages of 60 cm - 1.5 m / 23 in. - To get access to the menu in the Do steps 1–3 in 4.9 ft. width. The product moves in a pattern to cover display of the product on page 22 .
  • Page 26 Push the OK button. Note: To prevent that the grass in the narrow Use the arrow buttons and the OK button to passage is worn, Husqvarna recommends to set a low Settings > Lawn move through the menu structure Systematic Passage Mowing .
  • Page 27 charging station > Overview of search methods > guide wire method. After 11 min the product changes search method to the boundary wire method. Boundary > More > Test right / Test left . Push the START button and close the hatch. You can change the settings for how the product finds the charging station to adapt to the work area.
  • Page 28 To set the corridor width Note: Drive Past Wire , If you change the distance for To get access to the menu in the Do steps 1–3 in the distance will change along the boundary wire in all display of the product on page 22 . parts of the work area.
  • Page 29 Spiral cutting . Spiral Cutting does not Use the arrow buttons and the OK button to move the product to start Settings > Profiles > through the menu structure start in slopes steeper than 15%. Use profiles > Profile A, B, C > Select. Push the BACK button.
  • Page 30 Do steps 1–3 in This menu handles accessories mounted on the display of the product on page 22 . product. Contact your local Husqvarna representative for Use the arrow buttons and the OK button to move more information on available accessories.
  • Page 31 4.2.9.5 FlexiFence If you install the FlexiFence accessory, you must enable the FlexiFence function of the product. To enable the FlexiFence function To get access to the menu in the Do steps 1–3 in display of the product on page 22 . Use the arrow buttons and the OK button to move through the menu structure Settings >...

  • Page 32: Operation

    5 Operation 5.1 To use the ON/OFF button 5.2.1 Operating modes - Start Main area • WARNING: Read and understand the Secondary area • safety chapter before you use the product. Override schedule • • Spot cutting • Push the ON/OFF button for 3 seconds to set the 5.2.1.1 Main area product to ON.

  • Page 33: To Stop The Product

    Push the PARK button. When the product is new or has been stored for a long period, the battery can be empty and must be charged Operating Select an operating mode. Refer to Main area mode, before you can start the product. In the modes - Park on page 33 .

  • Page 34: Maintenance

    Push the maintenance tool down in 1 of the 4 running water from a water hose. positions, and pull the body up. Husqvarna recommends to use a special cleaning and Continue with the remaining positions while you maintenance kit, available as accessory. Speak to your hold the body up.

  • Page 35: Replacement Of The Blades

    WARNING: product. Husqvarna can only guarantee safety if you use Husqvarna Clean the blade disc and chassis with a brush. original blades with the embossed crowned At the same time, make sure that the blade disc H-mark logotype.

  • Page 36: Battery

    6.5 Winter service Take your product to your Husqvarna central service for service prior to winter storage. Regular winter service will maintain the product in good condition and create the best conditions for a new season without any disruptions.

  • Page 37: Troubleshooting

    In this chapter you can find information and help about faults and symptoms of the product. You can find more information and FAQ (Frequently Asked Questions) on www.husqvarna.com. 7.2 Fault messages The fault messages in the table below are shown in the display of the product. Speak to your Husqvarna representative if the same message shows frequently. Message...
  • Page 38 Message Cause Action Wheel motor Grass or other object is wrapped around the Clean the wheels and around the wheels. blocked, left/right drive wheel. Wheel motor overloa- ded, left/right Wheel drive problem, right/left Cutting system Grass or other object is wrapped around the Clean the wheels and around the wheels.
  • Page 39 PIN code to your registered e-mail address. If you have not registered the e-mail address, contact your local Husqvarna representative. No drive The product has got caught in something and Free the product and rectify the reason for has been slipping.
  • Page 40 Message Cause Action Charging current too Wrong or faulty power supply unit. Restart the product. If the problem stays high speak to your authorized service technician. Trapped The product is stuck in a small area behind a Check if there are any obstacles which make number of obstacles.

  • Page 41: Information Messages

    7.3 Information messages The information messages in the table below are shown in the display of the product. Speak to your Husqvarna representative if the same message shows frequently. Message Cause...

  • Page 42: Indicator Lamp In The Charging Station

    The indicator lamp in the charging station must show a solid or flashing green light for a correct installation. If not, follow the instructions in the troubleshooting guide below. Speak to your Husqvarna customer service for more information. Light Cause...

  • Page 43: Symptoms

    If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed answers to a number of standard questions. Contact Husqvarna customer service if you still cannot find the reason for the fault. Symptoms...

  • Page 44: Find Breaks In The Loop Wire

    Symptoms Cause Action The product is The product has reached its maximum cut- No action. Make an es- parked for hours in ting time for the day. Refer to the charging station. timate of the necessary operating time on page 23 . The hatch is closed but the START button is Push the STOP button to open the hatch.
  • Page 45 Check that the indicator lamp in the charging b) If the suspected boundary wire is long (thick station flashes blue, which indicates a break in black line) then do as follows: Put AL and GUIDE Indicator lamp in the the boundary loop. Refer to back to their original positions.
  • Page 46 Continue until only a very short section of the wire remains which is the difference between a solid green light and a flashing blue light. Then follow instruction in step 5 below. If indicator lamp still flashes blue in step 3 above: Put AL and GUIDE back in their original positions.

  • Page 47: Transportation, Storage And Disposal

    8.3.1 To remove the battery CAUTION: Only remove the battery when you dispose the product. When you remove the warranty seal, the Husqvarna warranty is no longer applicable. Remove the top cover and the body of the product. To clean the chassis and blade Follow steps 1-7 in disc on page 34 .

  • Page 48: Technical Data

    9 Technical data 9.1 Technical data ® ® ® Dimensions Automower Automower Automower Mark II Mark II Length, cm/in. 57/22.4 57/22.4 57/22.4 Width, cm/in. 43/16.9 43/16.9 43/16.9 Height, cm/in. 25/9.8 25/9.8 25/9.8 Weight, kg/lb 9.4/21 9.4/21 9.4/21 ® ® ® Electrical system Automower Automower...
  • Page 49 Output power 8 dBM Husqvarna AB does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, underground electric animal fencing or similar. Determined according to Directive 2006/42/EC and standard EN 50636-2-107. Except Sound level, perceived that is measured according to ISO 11094:1991.

  • Page 50: Registered Trademarks

    9.2 Registered trademarks ® Bluetooth Bluetooth SIG, inc. and any use of such word mark and logos are registered trademarks owned by marks by Husqvarna is under license. 50 - Technical data 1462 - 008 - 20.02.2023...

  • Page 51: Warranty

    The blades and wheels are seen as disposable and are not covered by the warranty. If an error occurs with your Husqvarna product, please contact Husqvarna customer service for further instructions. Please have the receipt and the product’s serial number at hand when contacting Husqvarna customer service.
  • Page 52 ® AUTOMOWER is a trademark owned by Husqvarna AB. © Copyright 2023 HUSQVARNA. All rights reserved. www.husqvarna.com Original instructions 1143080-26 2023-03-13...

This manual is also suitable for:

Automower 310 mark iiAutomower 315 mark ii

Table of Contents