Download  Print this page

Connect Vent; Complete Installation; Features And Benefits; Total Care™ System - Kenmore SENSOR SMART KING SIZE Capacity Plus Use & Care Manual

Hide thumbs

Advertisement

Table of Contents

Connect Vent

1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 4 in. (10.2 cm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
3. (On gas models) If flexible metal tubing is used, check to be
sure there are no kinks in the flexible gas line.

Complete Installation

1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of all packaging materials.
4. Check the dryer's final location. Be sure the vent is not
crushed or kinked.
5. Check to be sure the dryer is level. (See "Level Dryer.")
6. Plug into a grounded outlet. Turn power on.
7. Remove the blue protective film on the console and any tape
remaining on the dryer.
8. Read "Dryer Use."
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for 20
minutes and start the dryer.
If the dryer will not start, check the following:
Controls are set in a running or "On" position.
Start button has been pushed firmly.
Dryer is plugged into a grounded outlet.
Electrical supply is connected.
House fuse is intact and tight; or circuit breaker has not
tripped.
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat.
If you do not feel heat, turn the dryer off and check the
following:
There may be 2 fuses or circuit breakers for the dryer. Check
to make sure both fuses are intact and tight, or that both
circuit breakers have not tripped. If there is still no heat,
contact a qualified technician.
NOTE: You may notice a burning odor when the dryer is first
heated. This odor is common when the heating element is first
used. The odor will go away.
FEATURES AND
BENEFITS
TOTAL CARE™ System
The exclusive TOTAL CARE™ System combines the KING
SIZE™ load capacity, EVENHEAT™ with Auto Temp Control,
WRINKLE GUARD
®
III, and the TUMBLE FREE™ heated dryer
rack to ensure total drying care for any type of fabric and load
size.

Auto Temp Control

In automatic drying cycles, the temperature of the clothes is
reduced by automatically turning down the heat as the clothes
become dry. This reduces over drying and provides better care of
the fabrics in your clothes.
EVENHEAT™ with Auto Temp
Drying System
Control
The EVENHEAT™ with Auto Temp Control system for drying uses
dual moisture sensing devices and SENSOR SMART™ controls.
EVENHEAT™ with Auto Temp Control shortens drying time and
dries the load at lower temperatures for optimal fabric care. The
EVENHEAT™ with Auto Temp Control system monitors the
temperature of the heated air to ensure that it is never too hot to
cause fabric damage. It also terminates the cycle when the
clothes are dry to reduce shrinkage.

"Smart" Cool Down Period

When the selected level of dryness is reached, the dryer goes
into a cool down period lasting 2-10 minutes. Unlike other dryers
that provide a fixed 10-minute cool down, the length of the
"Smart" cool down is based on the cycle time and selected
dryness setting.
For small loads or loads that are dried at a lower temperature,
the cool down may be as low as 2 minutes.
For large loads or loads that are dried at a higher
temperature, the cool down will be closer to 10 minutes.

Jeans Cycle

Auto Temperature Control monitors the temperature and moisture
of your clothes and turns down the temperature at the right time.
By sensing the temperature and moisture, jeans come out of the
dryer ready to wear. You can put them on without them being
damp or overdry.
15

Advertisement

Chapters

Table of Contents
loading