Extron electronics NAV E 501 Setup Manual
  1. Manuals
  2. Brands
  3. Extron electronics Manuals
  4. Media Converter
  5. NAV E 501
  6. Setup manual

Extron electronics NAV E 501 Setup Manual

Hide thumbs Also See for NAV E 501:
Table of Contents

Advertisement

Quick Links

Download this manual
NAV E 501 and NAV E 101 • Setup Guide
This guide provides instructions for an experienced installer to install the Extron NAV E 501 and
NAV E 101 streaming encoders and to make all connections. One or more NAV encoders and one or
more compatible Extron NAV decoders form an AV distribution and switching matrix on a managed
1G IP network.
For more information on any subject in this guide, see the NAV E 501 and NAV E 101 User Guide, available at
NOTE:
www.extron.com.

Installation

Step 1 — Mounting
Turn off or disconnect all equipment power sources and rack or furniture mount the encoder as required.
Step 2 — Rear Panel Connections
INPUT
12V
2.0 A MAX
HDMI
J J
J
A
A A
INPUT
POWER
12V
1.5 A MAX
HDMI
Figure 1.
NAV E 501 and NAV E 101 Rear Panel Features
A
HDMI input port — Connect an HDMI cable between this port and the HDMI output port (or DVI port, with an appropriate adapter) of
the digital video source.
B
HDMI Loop Thru port — Connect a display to this female HDMI connector for local loop-through monitoring of the source signal.
LockIt
NOTE:
See
C
AUDIO input port — Connect balanced or unbalanced stereo audio input to this 5-pole, 3.5 mm captive screw connector (see
audio input
on page 6 to wire the connector).
D
Control Contact Closure port — Connect an Extron Show Me
the decoder, using the control system.
E
Control RS-232/IR port — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and IR communication with connected remote controlled devices. Control is accomplished using
an Extron control system (see
F
USB 2.0 port (NAV E 501 only) — Connect a USB Type-C cable from a USB host or a USB device. See
securely fasten the USB connector to the encoder.
NOTE:
This connector is limited to supplying 200 mA in USB device mode.
G
NAV 1G/PoE+ port — Connect to an Ethernet LAN on which one or more decoders also reside for streaming and control. This port
can also receive Power over Ethernet (PoE+) to power the encoder (see
H
Extension port (NAV E 501 only) — If desired, connect another networked device to this port. The port acts as a networked switch to
the NAV 1G/PoE+ port.
NOTE:
The Extension port cannot provide PoE.
I
Reset button and LED — This button initiates three modes of reset (see the NAV E 501 and NAV E 101 User Guide, available at
www.extron.com, for details).
J
Power Connector (optional) — Plug the included external 12 VDC power supply into this 2-pole connector for local power (see
connector
on page 6 to wire the connector and
AUDIO
L
R
LOOP THRU
B
B B
C C
C
AUDIO
L
R
LOOP THRU
Lacing Brackets
®
on page 6 to securely fasten the HDMI connectors to the encoder for
on page 6 to wire the connector).
Power
CONTROL
USB 2.0
CONT
RS-232
IR
C T Tx Rx G S G
5V/200 mA
D
D D
E
E E
F
F F
CONTROL
CONT
RS-232
IR
C T Tx Rx G S G
cable to the port to allow the encoder to select itself as the input to
®
Power
on page 3 for power options).
for power options).
NAV E 501
RESET
NAV 1G/PoE+
EXT
G
G G
H
H H
I
I I
NAV E 101
RESET
NAV 1G/PoE+
A
and
B
.
LockIt
Lacing Brackets
®
Analog
to
Power
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NAV E 501 and is the answer not in the manual?

Questions and answers

Related Manuals for Extron electronics NAV E 501

Summary of Contents for Extron electronics NAV E 501

  • Page 1 NOTE: The Extension port cannot provide PoE. Reset button and LED — This button initiates three modes of reset (see the NAV E 501 and NAV E 101 User Guide, available at www.extron.com, for details). Power connector (optional) — Plug the included external 12 VDC power supply into this 2-pole connector for local power (see...
  • Page 2 The port uses IP over USB technology. The IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also discoverable via Extron Toolbelt (see the NAV E 501 and NAV E 101 User Guide. The guide and Toolbelt are available for download at www.extron.com).
  • Page 3 The encoder is NOT operational until the boot process is complete (the Power LED is lit steadily). System Operation The encoder can be configured and controlled using embedded web pages or Toolbelt software (see the NAV E 501 and NAV E 101 User Guide available at www.extron.com).
  • Page 4 NAV E 501 / NAV E 101 • Setup Guide (Continued) Press the keyboard <Enter> key. The browser displays a privacy error message (see figure 3 at right for an example in the Chrome browser). Click Advanced (see figure 3, ). The button changes to Hide Advanced and explanatory text and a link appear below the button.
  • Page 5 1 1 1 1 * NAV E 501 only Figure 5. Home Page Detailed descriptions of communication, configuration, and monitoring are provided in the NAV E 501 and NAV E 101 User NOTE: Guide, available at www.extron.com. Connection settings View and change connection settings as follows: On the home page, click Settings (see figure 5, ) >...
  • Page 6 LockIt Lacing Brackets ® Plug the HDMI cable or USB (NAV E 501 only) into the panel connection (see , at right). Loosen the connection mounting screw from the panel enough to allow the LockIt lacing bracket to 3 3 3 be placed over it ( ).

This manual is also suitable for:

Nav e 101

Table of Contents