Table of Contents
Advertisement
Quick Links
NAV E 511 • Setup Guide
CLASS 1 LASER PRODUCT, see
WARNING:
The NAV E 511 outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution.
•
Do not look into the fiber optic cable connectors or into the fiber optic cables themselves.
•
Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
AVERTISSEMENT :
les yeux ; à utiliser avec précaution.
•
Ne pas fixer directement les connecteurs optiques ou les câbles fibre optique.
•
Associez les bouchons anti-poussière à l'ensemble émetteur/récepteur optique lorsque le câble fibre optique est débranché.
This guide provides instructions for an experienced installer to install the Extron NAV E 511 streaming encoder and to make all
connections. The Extron NAV encoder and one or more compatible decoders form an AV distribution and switching matrix on a managed
1G (1 Gbps) IP network.
NOTE
For more information on any subject in this guide, see the NAV E 511 User Guide, available at
:
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and rack or furniture mount the encoder as required.
Step 2 — Rear Panel Connections
INPUT
POWER
12V
2.0 A MAX
HDMI
J
J J
A A
A
Figure 1.
NAV E 511 Rear Panel Features
A
HDMI input port — Connect an HDMI cable between this port and the HDMI output port (or DVI port, with an appropriate adapter) of
the digital video source.
B
HDMI Loop Thru port — Connect a display to this port for local loop-through monitoring of the source signal.
NOTE:
See
LockIt
C
Audio input port — Connect balanced or unbalanced stereo audio input to this 5-pole, 3.5 mm captive screw connector (see
audio input
on page 6 to wire the connector).
D
Control Contact Closure port — Connect an Extron Show Me
the decoder, using the control system.
E
Control RS-232/IR port — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm, 5-pole captive screw
connector for bidirectional RS-232 and unidirectional IR communication with connected remote controlled devices using an Extron
control system (see
F
USB 2.0 port — Connect a USB Type-C cable from a USB host or a USB device. See
fasten the USB connector to the encoder.
NOTE:
This connector is limited to supplying 500 mA in USB device mode.
NAV E 511
Le NAV E 511 émettent une lumière invisible en continu (équipement de classe 1) qui peut être dangereuse pour
AUDIO
L
LOOP THRU
B
B B
C
C C
Lacing Brackets
on page 6 to securely fasten the HDMI connectors to the encoder for
®
Control connector
on page 6 to wire the connector).
User Guide at
www.extron.com
CONTROL
USB 2.0
R
CONT
RS-232
IR
C T Tx Rx G S G
5V/500 mA
D
D D
E
E E
F
F F
cable to this port to allow the encoder to select itself as the input to
®
.
www.extron.com
LAN
NAV 1G
EXT
G
G G
H
H H
A
LockIt
Lacing Brackets
®
.
NAV E 511
RESET
I
I I
and
B
.
Analog
on page 6 to securely
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Extron electronics NAV E 511
Summary of Contents for Extron electronics NAV E 511
- Page 1 CLASS 1 LASER PRODUCT, see WARNING: The NAV E 511 outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. • Do not look into the fiber optic cable connectors or into the fiber optic cables themselves.
- Page 2 IP over USB technology; the IP address is always 203.0.113.22 and CANNOT be changed. The CONFIG port is also discoverable via Toolbelt (see the NAV E 511 User Guide). The guide and Toolbelt are available for download at www.extron.com).
- Page 3 The encoder is NOT operational until the boot process is complete (the Power LED is lit steadily). NOTE: System Operation The encoder can be configured and controlled using embedded web pages or Extron Toolbelt (see the NAV E 511 User Guide available at www.extron.com and the Toolbelt Help file).
- Page 4 Connection via web pages Connection to the encoder and its embedded web pages can be made via either the front panel Configuration (USB) port (using IP over figure figure USB technology) (see on page 2) or the rear panel NAV 1G port (see on page 1).
- Page 5 1 1 1 1 HTML Page Figure 5. NOTE: Detailed descriptions of communication, configuration, and monitoring are provided in the NAV E 511 User Guide, available at www.extron.com. Connection settings View and change connection settings as follows: On the home page, click Settings (see figure 5, ) >...
- Page 6 Repeat step 2 for each decoder. Use a Tweeker or other small screwdriver to press and release the encoder front panel ID button. The encoder exits pairing mode. Repeat steps 1 through 4 to pair decoders to other encoders. After all devices are connected, powered on, and paired, the system is fully operational. Operation in a System with a NAVigator The Extron NAVigator is a system manager that easily configures and controls the NAV System.
Need help?
Do you have a question about the NAV E 511 and is the answer not in the manual?
Questions and answers