Related Manuals for Vanco Evolution EVEXKVM2
Summary of Contents for Vanco Evolution EVEXKVM2
- Page 1 4K HDBaseT ™ EXTENDER W I T H K V M Vanco Part Number EVEXKVM2 4K HDBaseT™ Extender with KVM www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 FEATURES INTRODUCTION The Evolution by Vanco EVEXKVM2 HDBaseT 2.0 Extender over Single Cat5e/6 with KVM, bi-directional IR, auto EDID/EQ, and PoC extends 4K/UHD and high definition video and audio with HDR, USB and IR signals, and power up to 230ft/70m over a single Cat5e/6 cable.
-
Page 4: Specifications
SPECIFICATIONS HDMI Signal .............. Supports HDMI 2.0 Resolutions Supported ..........480i/480P/576i/576P/720P/1080i/1080P/ 3D/3840×2160 Audio Supported ............LPCM, DTS and Dolby Digital Network Cable ............Cat5e/Cat6/Cat6a/Cat7 Transmission Length ..........3840x2160p@60Hz up to 230ft/70m IR ................Bi-directional, 20-60kHz USB ................ 2.0 USB Transmission ............480 Mbps @230ft/70m Working Temperature .......... -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS EVEXKVM2-TX (Transmitting Unit) 1. HDMI INPUT: Connect a source such as a Security NVR/DVR, computer, NAS system, etc. 2. Reset button 3. USB 2.0 type A port (connect the included USB cable to the source for KVM control) 4. - Page 6 PANEL DESCRIPTIONS EVEXKVM2-RX (Receiver Unit) 1. HDMI OUTPUT: Connect an HDMI display such as an HDTV or Projector 2. Reset button 3. USB 2.0 PORTS: Connect any 2.0 USB capable device such as a keyboard or mouse to control the source 4.
-
Page 7: Connection Diagram
CONNECTION DIAGRAM CONNECT AND OPERATE Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. Connect a single Category 5e/6/7 up to 164ft/50m to the UTP output of the Transmitting unit, and the other end to the UTP input of the Receiving unit. - Page 8 IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source, not simultaneously. There are two important things to note when setting up the IR system: 1.
- Page 9 IR RECEIVER (RX) • To control the source: Plug IR Receiver into IR RX port of receiver unit (EVEXKVM2-RX); place receiver at or near display. • To control the display: Plug IR Receiver into IR RX port of transmitter unit (EVEXKVM2-TX); place receiver in position where it is able to receive remote signals.
- Page 10 EDID Extended Display Identification Data (EDID) is a data structure provided by a digital display to describe its capabilities to a video source (e.g. graphics card or set-top box). In a nutshell, the display provides its EDID info to the source to send the proper signal format, this is essential for a proper handshake to occur. The EVEXKVM2 is equipped with EDID management, however there is no need to adjust any dip switches or dials, the unit automatically reads the EDID from the display and saves it internally.
- Page 11 NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. The transmission length is largely affected by the type of Cat5e/6 cables utilized, the type of HDMI sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m [1,000ft] bulk cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of fixed length patch cords).
-
Page 12: Resolutions Supported
RESOLUTIONS SUPPORTED Hactive Vactive Frequency 50Hz 60Hz 75/60Hz 75/60Hz 1024 75/60Hz 1280 60Hz 1280 1024 60Hz 1440 60Hz 1680 1050 60Hz 1280 25/30/50/60Hz 1920 1080 25/30/50/60Hz 3840 2160 24/30/60Hz www.vanco1.com... -
Page 13: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 14: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. -
Page 15: Technical Support
TECHNICAL SUPPORT In case of problems, please contact Vanco Technical Support by dialing 1-800-626-6445. You can also email technical support issues to techsupport@vanco1.com. When calling, please have the Model Number, Serial Number (affixed to the bottom of the unit) and Invoice available for reference during the call. - Page 16 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...