Related Manuals for Vanco Evolution EVEX4K70
Summary of Contents for Vanco Evolution EVEX4K70
- Page 1 HDMI® E X T E N D E R with Digital Audio Breakout, HDMI Loop-out, IR and PoE Vanco Part Number EVEX4K70 4K HDMI® Extender with Digital Audio Breakout, HDMI Loop- out, IR and PoE www.vanco1.com • 800.626.6445...
-
Page 2: Dear Customer
DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters. -
Page 3: Package Contents
FEATURES INTRODUCTION The Evolution by Vanco EVEX4K70 HDMI Extender over single Cat6 with Digital Audio Breakout, HDMI Loop-out, IR, and PoE, extends 4K@60Hz, 4:4:4 Chroma, and HDR10 up to 230ft/70m. Vanco’s patented bi-directional Power over Ethernet (PoE) Technology transmits power over Cat6, allowing either the Transmitter or Receiver to be powered without the use of a power supply for an easy installation. -
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance ............HDMI Deep Color 30/36/48 bit color depth, Full 3D HDCP Compliance ............Yes Video Bandwidth ............594 MHz Video Support ............480i/480p/720p/1080i/1080p/4Kx2K @60 Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio Input TMDS Signal ............. -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting Unit 1. Reset Button: Press to reset TX unit without having to disconnect power supply 2. Cat6 Output: Connect a single Cat6 with other end of cable connected to the RX unit (home-run cabling strongly recommended without any couplings, punch-downs, or patch panels) 3. - Page 6 PANEL DESCRIPTIONS Receiving Unit 1. Reset button: Press to reset RX unit without having to disconnect power supply 2. Cat6 Input: Connect a single Cat6 with other end of cable connected to the TX unit (home-run cabling strongly recommended without any couplings, punch-downs, or patch panels) 3.
-
Page 7: Connection Diagram
CONNECTION DIAGRAM HDTV Source IR Receiver IR Emitter IR Receiver HDMI HDMI IR Emitter CONNECT AND OPERATE Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit OPTIONAL: Connect a local display to the HDMI loop-out on the Transmitting unit Connect a single Cat6 (up to 230ft/70m) to the Cat6 output of the Transmitting unit, and the other end... -
Page 8: Ir Pass-Through
IR PASS-THROUGH IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source, not simultaneously. There are two important things to note when setting up the IR system: 1. -
Page 9: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 10: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. -
Page 11: Liability Statement
LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects. The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use. It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...