Related Manuals for Vanco EVEXHDARC
Summary of Contents for Vanco EVEXHDARC
- Page 1 HDBaseT™ 2.0 EXTENDER with ARC and Digital/ Analog Audio Breakouts Vanco Part Number EVEXHDARC HDBaseT™ 2.0 Extender with ARC and Digital/Analog Audio Breakouts www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 IR pass-through allows for source and/or display control. For extending HDMI signals over a single Cat6 with IR at a long distance, with Power over Cable, and maximum 4K and 1080p extension, the EVEXHDARC is a great plug and play solution for connecting the latest components! The EVEXHDARC includes two units: transmitting unit (EVEXHDARC-TX) and receiving unit (EVEXHDARC-RX).
-
Page 4: Specifications
*4K2K up to 330ft/100m using shielded Cat6, up to 70m using unshielded Cat5e in Normal Mode **1080@60Hz up to 492ft/150m using unshielded Cat5e/6 while in Long Reach Mode (LRM) PACKAGE CONTENTS • EVEXHDARC (TX & RX) • IR Blaster (TX) •... -
Page 5: Connection Diagram
CONNECTION DIAGRAM DVD Remote TV Remote IR TX IR TX Stereo Amplifier DVD/Blu-Ray Player IR RX IR RX Digital Optical Audio Digital Optical Audio Cat 5e/6 HDMI Cat 5e/6 Cat 5e/6 DVD/Blu-Ray Player Router Computer HDTV CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. -
Page 6: Panel Descriptions
PANEL DESCRIPTIONS EVEXHDARC-TX (Transmitting Unit) www.vanco1.com... - Page 7 EVEXHDARC-TX (Transmitting Unit) 1. Audio Out: Analog audio output, connect to an external amplifier or audio system using a 3.5mm audio cable 2. Audio In: Analog audio input, connect an audio source 3. Optical Out: Digital audio output, connect to an external amplifier or audio system using an optical audio cable 4.
- Page 8 PANEL DESCRIPTIONS EVEXHDARC-RX (Receiver Unit) www.vanco1.com...
- Page 9 EVEXHDARC-RX (Receiver Unit) Audio Out: Analog audio output, connect to an external amplifier or audio system using a 3.5mm audio cable Audio In: Analog audio input, connect an audio source Optical In: Digital audio input, connect to the digital audio source, typically the digital optical breakout on the display IR TX: Connect the included IR Transmitter (TX);...
-
Page 10: Ir Pass-Through
EDID The EVEXHDARC is equipped with EDID management, however there is no need to adjust any dip switches or dials, the unit automatically reads the EDID from the display and saves it internally. This feature was created for the installer in mind, for a plug and play installation! - Page 11 IR RECEIVER (RX) To control the source: Plug IR Receiver into IR RX port of receiver unit (EVEXHDARC-RX); place receiver at or near display. To control the display: Plug IR Receiver into IR RX port of transmitter unit (EVEXHDARC-TX); place receiver in position where it is able to receive remote signals.
- Page 12 BI-DIRECTIONAL ETHERNET The LAN ports located on the Transmitter and Receiver allows information and/or control to be sent over a local network or internet device using the Cat5e/6 and HDBaseT technology. Transfer rate supports up to 10/100 Mbps. This allows Ethernet to be combined with the HDMI signals, and other features to be extended to the opposite unit.
- Page 13 NOTICE Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. Incorrect placement of IR Transmitter and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 14: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug” concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 15: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 16 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...