Related Manuals for Vanco EVEX2004
Summary of Contents for Vanco EVEX2004
- Page 1 HDMI® E X TE N DER over single Coax Cable Vanco Part Number EVEX2004 HDMI® Extender over Single Coax Cable www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 FEATURES INTRODUCTION The Evolution by Vanco EVEX2004 HDMI Extender over Single Coax with Bi-directional IR extends high definition video and audio signals and IR, at a distance of up to 394ft/120m over RG6 coaxial cable, and 164ft/50m over RG59 coaxial cable. Features Bi-directional IR, which allows for control of the source or display.
-
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS HDCP Compliance ............Yes Video Bandwidth ............Single-link 225MHz [6.75Gbps] Video Support ............480i / 720p / 1080i / 1080p60 (Does NOT support 480p) Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio Transmission Range ........... -
Page 5: Package Contents
PACKAGE CONTENTS • EVEX2004 (TX & RX) • IR Blaster (TX) • IR Receiver (RX) • (2) DC 5V power supplies • Rack-mounting ear set • Product Manual PANEL DESCRIPTIONS Transmitting Unit Receiving Unit 11 12 HDMI IN: Connects to an HDMI source device with an HDMI male-to-male cable POWER/SIGNAL LED: Red light - POWER;... - Page 6 EDID The EDID dip switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the display and source. Pin #1 Pin #2 EDID feature 3G/HD/SD-SDI with multi-channel audio except DTS-HD Master & Dolby TrueHD 3G/HD/SD-SDI With stereo PCM audio HD/SD-SDI With stereo PCM audio EDID Learning Mode Factory Default: OFF - OFF...
-
Page 7: Connection Diagram
CONNECTION DIAGRAM BluRay® Player HDTV HDMI Transmitter Receiver HDMI Front Front IR Transmitter IR Receiver IR Transmitter IR Receiver Back Back HDMI over Coax Cable CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. -
Page 8: Ir Pass-Through
To control the source: Plug IR Blaster into IR TX port of transmitter unit (EVEX2004-TX); place blaster in front of the IR eye of the source. To control the display: Plug IR Blaster into IR TX port of receiver unit (EVEX2004-RX); place blaster in front of the IR eye of the display. - Page 9 NOTICE 1. Vanco HDMI and coaxial cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 10: Troubleshooting
HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. This activates all of the devices in corresponding order and results in a signal being plugged into a device that is on and will attempt to connect the signal. -
Page 11: Limited Warranty
Vanco’s opinion, prove defective within this warranty period, Vanco, at its option, will repair or replace this product without charge. Any defective parts replaced become the property of Vanco. This warranty does not apply to those products which have been damaged due to accident, unauthorized alterations, improper repair, modifications, inadequate maintenance and care, or use in any manner for which the product was not originally intended. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...