Related Manuals for Vanco Evolution EVEX2005
Summary of Contents for Vanco Evolution EVEX2005
- Page 1 HDMI® E X TE N DER over single Cat5e/Cat6 Cable Vanco Part Number EVEX2005 HDMI® Extender over Single Category 5e/6 Cable www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 INTRODUCTION The Evolution by Vanco EVEX2005 HDMI Extender over Single Cat5e/6 with Bi-directional IR and EDID management extends high definition video and audio signals and IR, at a distance of up to 131ft/40m over a single Cat5e/6 cable. Features EDID management, which allows and encourages source and display “handshake”...
-
Page 4: Specifications
SPECIFICATIONS TECHNICAL SPECS HDMI Compliance ............HDMI Deep Color, Full 3D HDCP Compliance ............Yes Video Bandwidth ............Single-link 225MHz [6.75Gbps] Video Support ............480i/480p/720p/1080i/1080p @60 HDMI over UTP ............Full HD (1080p)-40m (131ft) [CAT.X]; HD (720p/1080i)-50m (165ft) [CAT.X] Audio Support ............Surround Sound (up to 7.1 ch) or stereo digital audio Signal Equalization ............. -
Page 5: Package Contents
PACKAGE CONTENTS • EVEX2005 (TX & RX) • IR Blaster (TX) • IR Receiver (RX) • (2) DC 5V in line power supply • Rack-mounting ear set • Product Manual PANEL DESCRIPTIONS Transmitting Unit Receiving Unit 11 12 1. 5 V DC - Connect to 5V DC power supply 2. - Page 6 EDID The EDID dip switch allows for EDID learning or to pre-set an EDID to encourage a “handshake” between the display and source. Auto EDID Learning Mode 1. Set “MODE” on the transmitting unit EVEX2005-TX at 7 2. Follow the instruction in [Connect and Operate] to set up the EVEX2005 3.
-
Page 7: Connection Diagram
CONNECTION DIAGRAM CONNECT AND OPERATE 1. Connect a source such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI input on the Transmitting unit. 2. Connect a display such as an HDTV or HD Projector to the HDMI output on the Receiving unit. 3. -
Page 8: Ir Pass-Through
IR PASS-THROUGH IR Blaster TX IR Receiver RX IR BLASTER (TX) To control the source: Plug IR Blaster into IR TX port of transmitter unit (EVEX2005-TX); place blaster in front of the IR eye of the source. To control the display: Plug IR Blaster into IR TX port of receiver unit (EVEX2005-RX); place blaster in front of the IR eye of the display. - Page 9 NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 10: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...