Related Manuals for Vanco Evolution EVEXHDB1
Summary of Contents for Vanco Evolution EVEXHDB1
- Page 1 HDBaseT™ E X TE N DER 230ft/70m 4K UHD Vanco Part Number: EVEXHDB1 HDBaseT® Extender 230ft/70m 4K UHD www.vanco1.com • 800.626.6445...
- Page 2 DEAR CUSTOMER Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. This product is 100% inspected and tested in the United States to verify HDMI performance parameters.
- Page 3 FEATURES INTRODUCTION The EVEXHDB1 extender set consists of a transmitter and receiver. HDMI signals are input into the transmitter and HDBaseT technology is used to transmit the audio/video signals to the receiver up to 70m via a single Cat5e/Cat6 cable for 1080p and 40m at 4K 60Hz.
-
Page 4: Specifications
SPECIFICATIONS Input Signal ............... TX: 1 HDMI,1 IR; RX: 1 IR, 1 RJ-45 Input Connector ............TX: HDMI female, 3.5mm mini jack; RX: 3.5mm mini jack; RJ-45 Video Signal .............. HDMI1.4 Audio ................ Digital audio, transmit through HDMI audio Output ..............TX: 1 RJ-45, 1 IR; RX: 1 HDMI, 1 IR Output Connector ............ -
Page 5: Panel Descriptions
PANEL DESCRIPTIONS Transmitting Unit Receiving Unit 1. HDMI IN: Connect to HDMI source. 7. HDMI Out: Connect to HDMI display. 2. IR IN: Connect to an IR receiver, the IR signal 8. IR IN: Connect to an IR receiver, the IR signal received from this port can only send out via received from this port can only send out via HDBaseT Receiver. -
Page 6: Connection Diagram
CONNECTION DIAGRAM CONNECT AND OPERATE 1. Connect HDMI source (such as Blue-ray DVD) to HDMI In port of the transmitter with an HDMI cable. 2. Connect HDBaseT OUT port of the transmitter to the HDBaseT IN port of the receiver through a CAT5e/ CAT6 cable. - Page 7 IR PASS-THROUGH The bi-directional IR system allows you to control the source that is connected to the extender unit, from the display; or the display from the source, not simultaneously. There are two important things to note when setting up the IR system: 1.
- Page 8 Below is the voltage and pinout used for IR of the EVEXHDB1. Due to possible differences in 3rd party IR cables, please use the IR cables that came with the product. www.vanco1.com...
- Page 9 NOTICE 1. Vanco HDMI and Cat5e/6 cables are strongly recommended for use with this product to ensure best results. 2. Incorrect placement of IR Transmitter and Receiver may result in the failure of the IR extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.
-
Page 10: Troubleshooting
4. If you are still encountering issues, attempt the “hot-plug” concept. With all of the HDMI cables disconnected, turn on the source and plug in the HDMI cable into it’s output, then power up the Vanco unit and plug the HDMI cable into it’s input, finally turn on the display and plug the HDMI cable from the receiver into it. -
Page 11: Limited Warranty
If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt/sales invoice or other acceptable proof of purchase to the seller of this equipment. The seller will then contact Vanco regarding warranty repair or replacement. - Page 12 ® Vanco International 506 Kingsland Drive Batavia, Illinois 60510 call: 800.626.6445 fax: 630.879.9189 visit: www.vanco1.com...