1. Manuals
  2. Brands
  3. Sony Manuals
  4. Storage
  5. PetaSite DMS-B150L
  6. Installation manual

Sony PetaSite DMS-B150L Installation Manual

Digital mass storage system
Hide thumbs Also See for PetaSite DMS-B150L:
Table of Contents

Advertisement

Quick Links

Download this manual
DIGITAL MASS STORAGE SYSTEM
DMS-B150L
DMS-B210S
DMS-B80L
DMS-B110S
DMS-EX150L
DMS-EX210S
EXTENSION CABLE KIT
DMSA-CBL1
EXTENSION BELT KIT
DMSA-BLT2/BLT6
TERMINAL SERVER
DMSA-TS08/TS16
TERMINAL SERVER KIT
DMSA-TS08K
TERMINAL SERVER CABLE
DMSA-CTS/CTL
ETHERNET HUB
DMSA-EH16
INSTALLATION MANUAL
1st Edition (Revised 3)
AC ADAPTER
DMSA-EHAC/EHACK
ETHERNET CABLE
DMSA-CES/CEL
POWER CORD
DMSA-CPJ/CPE
ATTACHMENT KIT
DMSA-AT80
SCSI BUS EXPANDER KIT
DMSA-SBE1
AC POWER CABLE KIT
DMSA-CBJ80/CBJ15/CBJEX

Advertisement

Table of Contents
loading

Related Manuals for Sony PetaSite DMS-B150L

Summary of Contents for Sony PetaSite DMS-B150L

  • Page 1 DIGITAL MASS STORAGE SYSTEM DMS-B150L DMS-B210S DMS-B80L DMS-B110S DMS-EX150L DMS-EX210S EXTENSION CABLE KIT AC ADAPTER DMSA-CBL1 DMSA-EHAC/EHACK EXTENSION BELT KIT ETHERNET CABLE DMSA-BLT2/BLT6 DMSA-CES/CEL TERMINAL SERVER POWER CORD DMSA-TS08/TS16 DMSA-CPJ/CPE TERMINAL SERVER KIT ATTACHMENT KIT DMSA-TS08K DMSA-AT80 TERMINAL SERVER CABLE SCSI BUS EXPANDER KIT DMSA-CTS/CTL DMSA-SBE1...
  • Page 2 ! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.

  • Page 3: Table Of Contents

    Table of Contents Manual Structure Purpose of this manual ....................3 Related manuals ......................3 Contents ........................3 Trademarks ........................ 4 1. Overview 2. Unpacking 2-1. Unpacking the Console ................2-1 2-1-1. Basic Console (DMS-B150L/B210S) and Accessories ..... 2-1 2-1-2. Basic Console (DMS-B80L/B110S) and Accessories ....
  • Page 4 5. About Installation Work 5-1. Notes during Installation ................5-1 5-2. Tools ......................5-2 6. Installation Procedure 6-1. Installation Flow ..................6-1 6-2. Removal and Installation of the Cabinets ........... 6-2 6-3. Removal of the Shipping Metal Fixtures ............ 6-6 6-4.

  • Page 5: Manual Structure

    Manual Structure Purpose of this manual This manual is the installation manual of PetaSite Digital Mass Storage System DMS-B150L/B210S/B80L/B110S/EX150L/EX210S, DMSA-CBL1/BLT2/BLT6. This manual is intended for use by trained system and service engineers, and describes the information when installing. Related manuals The following manuals are prepared for DMS-B150L/B210S/B80L/B110S/EX150L/ EX210S.

  • Page 6: Trademarks

    Trademarks Registered trademarks used in this manual are as follows. . WindowsNT is a registered trademark of Microsoft Corporation. . Solaris is a trademark of Sun Microsystems Inc.. DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...

  • Page 7: Overview

    Section 1 Overview The PetaSite DMS-B150L/B210S/B80L/B110S/EX150L/EX210S controls the many cassette tapes that are used in the DTF digital tape streamer so that huge volumes of data can be stored, searched, recorded and played back. It is used as the key equipment.

  • Page 9: Unpacking

    Section 2 Unpacking 2-1. Unpacking the Console . A forklift is required to unpack the console. . The console has casters to facilitate movement. . Take care when handling the console. Damage and transformation of the X rail that has been attached to the floor and ceiling inside the console could cause a failure or malfunction.
  • Page 10 2-1. Unpacking the Console Unpacking Procedure 1. Cut the four bands. 2. Remove the top cap. 3. Remove the six metal fasteners and remove the panel (front) and panel (rear). 4. Prepare the spacer and standard accessory and remove the plastic bag from the console. 5.

  • Page 11: Basic Console (Dms-B80L/B110S) And Accessories

    2-1. Unpacking the Console 2-1-2. Basic Console (DMS-B80L/B110S) and Accessories Outside view Forklift labels Band Top cap Panel (rear) Forks of forklift DMS-B80L/B110S Spacer Supplied accessories of the package supporting equipment Metal fasteners Standard Accessory box Bottom table accessory Supplied accessory of the package supporting equipment Accessory box...

  • Page 12: Extension Console (Dms-Ex150L/Ex210S) And Accessories

    2-1. Unpacking the Console 2-1-3. Extension Console (DMS-EX150L/EX210S) and Accessories Outside view Band Forklift labels Top cap Supplied accessories Supplied accessories of the package of the package supporting equipment supporting equipment Standard accessory DMS-EX150L/ Forks of forklift EX210S Accessory box Metal fasteners Panel (rear) Metal...
  • Page 13 2-1. Unpacking the Console Unpacking Procedure 1. Cut the four bands. 2. Remove the top cap. 3. Remove the six metal fasteners and remove the panel (front) and panel (rear). 4. Remove the polyethylene bag from the console. 5. Align the forks of the forklift with the forklift labels on the side of the console, hold up the bottom of the console and move down from the bottom table.

  • Page 14: Dmsa-At80 And Accessory List

    2-2. DMSA-AT80 and Accessory List 2-2. DMSA-AT80 and Accessory List Outside view Spacer Cushion Cable duct (80) Spacer Accessory (Tie band, Cushion repeat tie) Spacers FC mounting plate (80) Cable clamps2 Cushion FC bracket L (15)/ Accessory (screw) FC bracket R (15) Spacer PC bracket (80) Spacer...

  • Page 15: Dmsa-Eh16 And Accessory List

    2-3. DMSA-EH16 and Accessory List 2-3. DMSA-EH16 and Accessory List Outside view Document Spacer Accessory Main unit Corner cushions Corner cushion Corner cushions Corner cushions Packing carton Types and quantity of accessories . Hub bracket 1 : . Hub bracket 2 : .

  • Page 16: Dmsa-Sbe1 And Accessory List

    2-4. DMSA-SBE1 and Accessory List 2-4. DMSA-SBE1 and Accessory List Outside view Accessory Accessories Document Cushion Spacer Main unit Cushion Packing carton Types and quantity of accessories . Disk array cable (SHORT) : . Monitor fixing plate : . Belt : .

  • Page 17: Dmsa-Ts08/Ts16/Ts08K And Accessory List

    2-5. DMSA-TS08/TS16/TS08K and Accessory List 2-5. DMSA-TS08/TS16/TS08K and Accessory List Outside view Document TS08 accessory TS08K accessory TS16 Spacer accessory Corner cushion Corner cushions Corner cushions Main unit Packing carton Types and quantity of accessories . Cord with connector (T. S. SETUP) : .

  • Page 19: Installation Environment And Machine Mass

    Section 3 Installation Environment and Machine Mass For safety and stable performance, use the DMS-B150L/B210S/B80L/B110S/EX150L/EX210S under the appropriate environment as described below. The floor on which the console is placed must have at least the specified strength. 3-1. Installation Environment .

  • Page 20: Installation Space

    3-3. Installation Space 3-3. Installation Space The front side of the consoles should be at least 80 cm away from walls, and the rear side of the consoles should be at least 100 cm way from walls. In addition, leave a space of at least 70 cm above the consoles. DMS-B150L/B210S DMS-EX150L/EX210S DMS-B80L/B110S...

  • Page 21: Power Supply

    Section 4 Power Supply 4-1. AC Power for DMS-B150L/B210S/B80L/B110S Be sure to use the equipment within the specified range of power supply voltage. AC120 V ±10 %, 60 Hz ±0.5 % 8.3 A (peak 16.7 A 10 ms) Power voltage : AC220 V ±10 %, 50/60 Hz ±0.5 % 4.6 A (peak 9.1 A 10 ms) AC230 V ±10 %, 50/60 Hz ±0.5 % 4.4 A (peak 8.7 A 10 ms) AC240 V ±10 %, 50/60 Hz ±0.5 % 4.2 A (peak 8.4 A 10 ms)
  • Page 22 4-1. AC Power for DMS-B150L/B210S/B80L/B110S How to use the plug holder Protect the plug using the plug holder so that the plug cannot be easily removed from AC outlet. After the power cord plug is securely connected to AC outlet, attach the Plug holder plug holder to the power cord.

  • Page 23: Ac Power For Dmsa-Ts08/Ts16

    For AC100 V : Use the DMSA-CPJ (for Japan). For AC120 V : Use the DMSA-CPE (for U.S.A. and Canada). If the unit is used in the area except above, please contact your local Sony Sales Office/Service Center. 4-3. AC Power for DMSA-SBE1...

  • Page 25: About Installation Work

    Section 5 About Installation Work 5-1. Notes during Installation Safety installation Two or more people must install the equipment, at least one of whom must be trained. Storage of parts Store the outside cabinets removed during installation in a safe place to avoid damage. Also store the removed parts and the unpacked parts that are supplied with the series consoles as well as the outside cabinets.

  • Page 26: Tools

    5-2. Tools 5-2. Tools The following tools are necessary to install the console. Description Size Part No. Open end wrench 7 x 8 mm J-7120-020-A Open end wrench 27 x 30 mm J-7120-010-A Hexagon L wrench 10 mm across (extension console) 7-700-736-00 (12 wrenches per set) Phillips screwdriver...

  • Page 27: Installation Procedure

    Section 6 Installation Procedure 6-1. Installation Flow Installation of console and peripheral equipment Removal and installation of the cabinets When the system is carried in to the installation location with (Basic console) the same configuration as in the shipment from the factory, this work is not necessary.

  • Page 28: Removal And Installation Of The Cabinets

    6-2. Removal and Installation of the Cabinets 6-2. Removal and Installation of the 2. While pulling down portion A shown in the illustration Cabinets in the direction of the arrow, remove upward the drive stage panel from the pin on portion B. Then, pull out If there is not enough space to install the parts, remove the the panel from the console.
  • Page 29 6-2. Removal and Installation of the Cabinets 2. Table top 3. Stage panel support Removal Removal 1. Open the drive stage panel. (Refer to “1. Drive stage 1. Remove the drive stage panel. (Refer to “1. Drive panel”.) stage panel”.) 2.
  • Page 30 6-2. Removal and Installation of the Cabinets 4. Drive stage 5. Unlock the right and left rails in the direction of the arrow and push them. Removal Lock levers Each drive stage has a number on it. Be sure to attach a removed drive stage to the original position while referring to the following figure.
  • Page 31 6-2. Removal and Installation of the Cabinets 5. Front top plate, front base plate, side panels Loosen the two hexagonal head cap bolts and remove (FL/FR) the two screws on side panel (FL). Remove the side panel (FL) in the direction of the arrow. Loosen the two hexagonal head cap bolts and remove Removal the two hexagonal head cap bolts on side panel (FR).

  • Page 32: Removal Of The Shipping Metal Fixtures

    6-3. Removal of the Shipping Metal Fixtures 6-3. Removal of the Shipping Metal 1. Rear door Fixtures Removal The transfer assembly and the carrier assembly are fixed inside the console by shipping metal fixtures to avoid 1. Remove the six screws (with drop-safe) in the DMS- damage during shipment.
  • Page 33 6-3. Removal of the Shipping Metal Fixtures 2. Shipping metal fixture of the Y-axis direction 2. While pulling down portion A shown in the illustration in the direction of the arrow, remove upward the rear door from portion B. Then, remove the door from the console. Removal Be careful not to drop the φ...
  • Page 34 6-3. Removal of the Shipping Metal Fixtures 3. Shipping metal fixture of X-axis direction 3. Move the carrier assembly to the position to facilitate replacement work. Fix the carrier assembly by inserting a screwdriver or the like into the Y-rail. Removal .
  • Page 35 6-3. Removal of the Shipping Metal Fixtures 4. Attach the removed upper shipping metal fixture (X) us- 4. Shipping metal fixture of the Z-axis direction ing the hexagonal head cap bolts that were attached at step 4 of “2 Shipping metal fixture of the Y-axis direction” in Removal the direction of the arrow, move the shipping metal fixture to the front, then fix it in the direction of the arrow.

  • Page 36: Installation Of The Basic Console

    6-3. Removal of the Shipping Metal Fixtures 6-4. Installation of the Basic Console 6-4. Installation of the Basic Console Checks after Removing the Shipping Metal Fixtures After removing the shipping metal fixtures, check the Installation Location following. 1. After the removal procedure is complete, check that all Move the basic console to the location where it is to be installed.
  • Page 37 6-4. Installation of the Basic Console 5. Respectively rotate the four floor levelers by 180d with Fixing the Console a spanner. (In case of 3 to 6 extension consoles) 6. Fasten the nut. 1. Check that height of the point A is 110 mm above the (Use a spanner of 30 mm across.) floor.

  • Page 38: Connecting Extension Consoles

    6-5. Connecting Extension Consoles 6-5. Connecting Extension Consoles 3. Remove the side fixing bracket of the basic console. (1) Remove the ten screws and remove the side plate This section describes how to connect extension consoles. support (side) at the right and left. One or two consoles can be connected when the extension belt kit DMSA-BLT2 is used, 3 to 6 extension consoles can be connected when the extension belt kit DMSA-BLT6...
  • Page 39 6-5. Connecting Extension Consoles (3) Loosen the two screws (a) and the screw (b) to remove 5. Remove the drive stage panel of the extension console. the side plate support (top) in the direction of the (1) Loosen the two screws (with drop-safe) and open the arrow.
  • Page 40 6-5. Connecting Extension Consoles 6. Remove the drive stage. (4) Release the locks of the right and left rails in the direction of the arrows as shown and push in the rails. Each drive stage is numbered. Be sure to re-attach the removed drive stages at the Lock levers same position while referring to the figure below.
  • Page 41 6-5. Connecting Extension Consoles 8. Move the X rail (top) of extension console in the 9. Move the X rail (bottom) of extension console in the direction opposite to the connection side. direction opposite to the connection side (1) Remove the two hexagonal head cap bolts (a) securing (1) Loosen the four hexagonal head cap bolts (M4 x 25) the X rail of the extension console.
  • Page 42 6-5. Connecting Extension Consoles 2. Connecting the Console 2. Fix both consoles with the eight hexagonal head cap bolts (M4 x 8) supplied with the extension console. 2-1. When connecting a single or two extension 3. Open the flat cable clamp of the extension console and consoles connect the flat cable to the connector (CN102 : SE- 1.
  • Page 43 6-5. Connecting Extension Consoles 2-2. When connecting the extension consoles in 2. Fix both consoles with the eight hexagonal head cap the range of 3 to 6 bolts (M4 x 8) supplied with the extension console. 3. Measure the dimensions A-A of the X reference pins 1.
  • Page 44 6-5. Connecting Extension Consoles . If the accumulated difference of the bottom side is 3. When Connecting Two or More Extension Consoles smaller, rotate the two casters that are located far from the basic console, by 30 degrees clockwise, 3-1. Connecting the second extension console (In insert the spacer into C (at two locations in the case of connecting two extension consoles) front and rear) and fix them by the eight hexagonal...
  • Page 45 6-5. Connecting Extension Consoles 6-5. Connecting Extension Consoles 5. Connecting the X Rail (Top) 4. Fix the hexagonal head cap bolt (d) with the nut until 1. Slide the X rail (top) of the extension console in the the bolt does not become loose. (User the wrench of direction of the arrow.
  • Page 46 6-5. Connecting Extension Consoles 6. Connecting the X Rail (bottom) 7. Removing the X Belt 1. Slide the X rail (bottom) of the extension console in 1. When connecting an extension console at a latter time, the direction of the arrow until it contacts with the X fix the X-axis shipping metal fixture (top)/(bottom) of rail of the basic console.
  • Page 47 6-5. Connecting Extension Consoles 3. Remove the four hexagonal head cap bolts (M4 x 8) 5. Loosen the hexagonal head cap bolt (c) of the upper X and move the X stopper (T)/(B) from the basic console tension assembly to lighten the load of the spring. to the same position of the end console (the console 6.
  • Page 48 6-5. Connecting Extension Consoles 8. Installing the X Belt 11. Remove the six hexagonal head cap bolts (M3 x 12) 1. Route the X belt between the synchro shaft and X belt connecting the X belt (top), six spring washers and six pulley (top)/(bottom).
  • Page 49 6-5. Connecting Extension Consoles (2) Route the upper X belt on top of the flexible 3. Attach the X belt on the upper pulley of the synchro board. shaft. Fix the X belt pulley assembly (top) with the two (3) Be careful of the upward and downward directions washers (D4) and the two hexagonal head cap bolts (M4 x 14) (b), and attach it to the extension end condole.
  • Page 50 6-5. Connecting Extension Consoles 6. Attach the belt fixing panel (X) to the X slider (top) 9. Rotate the hexagonal head cap bolt (c) that is removed with the two hexagonal head cap bolts (M5 x 12). in step 9 of “7. Removing the X Belt”, of the X tension assembly fully in the direction of loosening the spring, The hexagonal head cap bolt must be attached in the then attach the X tension assembly to the end console...
  • Page 51 6-5. Connecting Extension Consoles 13. Confirm the X belt tension. Hang the fan tension scale on the front side (side of the rear door) of the X belt and measure the tension. (1) Move the transfer assembly to the specified position as shown in the figure.
  • Page 52 6-5. Connecting Extension Consoles 9. Phase Adjustment 3. Return the phase adjustment pin to its original posi- 1. Move the transfer to the extension console side and tion. move the phase adjustment pin of the basic console to Tightening torque : 0.8 N.m (8 kgf.cm) its adjustment position.
  • Page 53 6-5. Connecting Extension Consoles 10. Applying Grease 11. Setting the Console 1. Use a thin brush and apply grease (Molykote grease 1. Change the setting of the switch (S1) on the SE-590 PG-663 : 7-640-004-53) thin on the entire surface of board of the basic console and extension console.

  • Page 54: Installation Of Dmsa-Cbl1

    6-6. Installation of DMSA-CBL1 6-6. Installation of DMSA-CBL1 (2) Remove the three connectors of the harness that is located under the carrier assembly. 1. Removing the Parts from Basic Console 1-1. Carrier assembly (1) Move the carrier assembly to the height that facilitate the installation work.
  • Page 55 6-6. Installation of DMSA-CBL1 (4) Remove the two hexagonal head cap bolts (M4 x 14) 1-2. Robot cable assembly that fix the carrier assembly. (5) Raise the carrier assembly a little. (In the direction of arrow A) When removing the robot cable assembly, be careful not (6) Remove the carrier assembly by rotating the carrier contact the fragile parts such as reflector plate with other assembly centering around the upper reference pin...
  • Page 56 6-6. Installation of DMSA-CBL1 (5) Remove the connector from the small-parts harness (9) Among the screws that fix the Y harness bracket (2), (UVW-BY) that is located on top of the Y rail. loosen the top screw and remove the lower two screws. (6) Cut all the bands that fix the cables to the Y rail.
  • Page 57 6-6. Installation of DMSA-CBL1 1-4. Cable relay plate 2. Attach the five types of cables to the cable relay plate (1) Remove the four screws. (EXD). (Insert the flat cable to CN2 of the CB-106 (2) Remove the two connectors from the cable relay plate. board.) Cable relay plate (EXD) Cable relay plate...
  • Page 58 6-6. Installation of DMSA-CBL1 4. Fix the cable relay plate (EXD) to the second exten- 8. Connect the five types of cables to the mating cables sion console with the three screws (PWH 4 x 8). of the basic console. 5.
  • Page 59 6-6. Installation of DMSA-CBL1 3. Installing the Guide Channel 4. Push the guide channels (2-1) assembly, (3) assembly, 1. Attach the guide spacer (1) with the two screws (2-2) assembly in the directions of A and B. Then fix (PWH4 x 8). them with the four screws (PWH4 x 8).
  • Page 60 6-6. Installation of DMSA-CBL1 4. Installing the Robot Cable (EXD) Assembly 4. Insert the X cable bracket (EXD) to the shaft of the Y base lower assembly. Fix it using the three screws When installing the robot cable (EXD) assembly, be among the four screws that are removed from the X careful not contact the fragile parts such as reflector plate cable bracket of the robot cable assembly.
  • Page 61 6-6. Installation of DMSA-CBL1 10. Connect the five connectors of the cable to the mating Fix the cable carefully so that the cable must not contact connector of the cable relay plate (EXD). with the synchro shaft or frame’s side panel. .
  • Page 62 6-6. Installation of DMSA-CBL1 5. Installing the Idler Assembly 12. Route the top of the SV cable cover (EXD2) through the four screws of the guide channel (3) assembly and Install the idler (upper) assembly and the idler (lower) fix it with the two screws (PWH4 x 8) to the metal assembly with the two screws (PWH4 x 8) and hook the plate of the runner flex.

  • Page 63: Prevention Of Falling

    Fix the console (For more details, please contact your local Sony Sales using either method according to the installation location.
  • Page 64 6-7. Prevention of Falling Fig.1 : DMS-B150L/B210S 1350 1180 4-M12 nut DMS-EX150L/EX210S 4-M12 nut Mark : Eyebolt fixing hole (Unit : mm) 6-38 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 65 6-7. Prevention of Falling Fig.2 : DMS-B150L/B210S 1035 4-φ 8.2 hole Fixing metal Fixing metal attachment position attachment position 1350 1170 41.5 31.5 1293 Fixing metal attachment position 4-φ 8.2 hole 1035 (Unit : mm) 6-39 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 66 6-7. Prevention of Falling Fig.3 : DMS-B80L/B110S 4-φ 8.2 hole Fixing metal Fixing metal attachment position attachment position 1100 41.5 31.5 1043 Fixing metal attachment position 4-φ 8.2 hole Fixing metal attachment position (Unit : mm) 6-40 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 67 6-7. Prevention of Falling Fig.4 : DMS-EX150/EX210S 4-φ 8.2 hole Fixing metal attachment position 4-φ 8.2 hole Fixing metal attachment position (Unit : mm) 6-41 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...

  • Page 68: Voltage Selector Setting And Notes

    6-8. Voltage Selector Setting and Notes 6-8. Voltage Selector Setting and Notes 1. Setting the voltage selector Connect the harness connectors to the connectors of CN2 to CN6 on the VS-61 board and set the voltage Before turning on the power, check the setting of the values.

  • Page 69: Installation Of The Tape Drive

    . DRIVE FOOT ASSYs : 4 pcs drive will fall over and cause serious injury. (Sony part number : X-3605-849-1) . Two or more persons must work together to install the DTF tape drive.
  • Page 70 6-9. Installation of the Tape Drive (2) Loosen the two fixing screws of the drive drive stage (4) Slide the tape drive to the back of the drive stage. and pull out the drive stage until the lock levers of the Install the tape drive until the legs on the rear panel right and left rails are locked.
  • Page 71 6-9. Installation of the Tape Drive 2. Installing in the top stage of the drive stage Before installing the tape drive in the top stage, remove the bin assembly and the side bin plate that occupy the space of the tape drive. Then, install the tape drive in the top stage in the same manner as the bottom stage.
  • Page 72 6-9. Installation of the Tape Drive Illustration shows the installation work in case of DMS-B150L. Illustration shows the installation work in case of DMS-B80L. When installing the third tape drive When installing the fourth tape drive Remove the two side bin plates of 1 and the bin assembly of 2. Remove the two side bin plates of 1 and the bin assembly of 2.

  • Page 73: Extension Console

    6-9. Installation of the Tape Drive 6-9-2. Extension Console Removing the Bin Assembly 1. While referring to “1. Rear door _ Removal” of The GY-2120 or GY-8240/DIR-240 and VTR of 4U (or Section “6-3. Removal of the Shipping Metal Fix- 5U) can be installed in the extension console.
  • Page 74 6-9. Installation of the Tape Drive 1. Setting for installing the 4U drive (4) Loosen the three screws and open the rear door. To install the 4U drive, change the height of the drive RK4 x 20 (with drop-safe) stages. Only the bottom drive stage or both of top and bottom drive stages can be set for 4U drive.
  • Page 75 6-9. Installation of the Tape Drive (6) Remove the slide rails of the drive stage whose setting (8) Align the lower square hole on the stage support (F) is to be changed. with the projected portion A of the metal plate and change the attachment position.
  • Page 76 6-9. Installation of the Tape Drive If the reference pins are caught, do the following adjustment. 1 Loosen the eight screws (PWH4 x 8) fixing the drive stage, push in the drive stage, then tighten the loosened eight screws. In this status, open and close the drive stage.
  • Page 77 6-9. Installation of the Tape Drive 2. Installing in the bottom stage of the drive (3) The holes of the drive stage that are used to fix the stage tape drive or the VTR, are different depending upon (1) Remove the drive stage panel while referring to the drive whether it is tape drive or VTR.
  • Page 78 6-9. Installation of the Tape Drive 3. Installing in the top stage of the drive stage (4) Align the VTR (or tape drive) with the positioning holes of the stage and install the VTR (or tape drive). The top stage of the drive stage is occupied by the bin Front panel VTR (or tape drive) assembly when shipped from the factory.
  • Page 79 6-9. Installation of the Tape Drive (3) Attach the supplied EX stage supports UL/UR with the (6) Attach the four screws and reinforcement angle that six screws (PWH4 x 8). were removed in step 4 to the bin side as shown in the figure.

  • Page 80: Routing The Cables To Be Connected To The Drives

    6-9. Installation of the Tape Drive 6-9-3. Routing the Cables to Be Connected 3. Attach the six tie mounts using the screws fixed on the to the Drives frame or the screws supplied. 4. Bundle the cables at the tie mount using the tie band. After mounting the drives in the console, route the cables 5.

  • Page 81: Setting The Switches

    6-10. Setting the Switches 6-10. Setting the Switches 2. Setting the switches (CB-105 board) . Do not change the settings of the switches shown as When removing the bin assembly, set the switches on the “factory use only”. CB-105 board in order to mount the drive in the upper .
  • Page 82 6-10. Setting the Switches 4. Operations after switch setting The relationship between changing the drive installation areas and the drive setting switches are as follows. After changing the switch setting, renew the PSC setup. Do the following setting after installation is complete. DMS-B150L /B210S / EX150L /EX210S 1.

  • Page 83: Installing The Package Supporting Equipment

    Terminal server Installation of the DMSA-SBE1 bracket (80/ETS8) (Refer to Section 6-11-7.) (For customers in Japan only.) Terminal server bracket (80/ETS8) If the unit is used in the area except above, please contact your local Sony Sales Office/Service Center. 6-57 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 84 6-11. Installing the Package Supporting Equipment When Installing the DMSA-TS08 in the Extension When Installing the DMSA-TS16 in the Basic Console (EX150L/EX210S) Console (B150L/B210S) 1. Set the POWER switch of the DMSA-TS08 to the I 1. Set the POWER switch of the DMSA-TS16 to the I (ON) position.
  • Page 85 6-11. Installing the Package Supporting Equipment 2. Fix the DMSA-TS16 with the belt that has passed When Installing the DMSA-TS16 in the Extension through the monitor fixing plate. Console 1. Set the POWER switch of the DMSA-TS16 to the I (ON) position.
  • Page 86 6-11. Installing the Package Supporting Equipment 6-11-2. Installation of the DMSA-EH16/EHAC/ 4. Install it in the console with the two screws (PWH4 x EHACK When Installing It in the Basic Console 1. Install the hub bracket 2 in the rear of the DMSA- EH16.
  • Page 87 6-11. Installing the Package Supporting Equipment 4. Install it in the console with the four screws (PWH4 x When Installing It in the Extension Console 1. Install the hub bracket 2 in the rear of the DMSA- EH16. PWH4 x 8 2.

  • Page 88: Installation Of The Dmsa-Cbj80/Cbj15/Cbjex

    6-11. Installing the Package Supporting Equipment 6-11-3. Installation of the DMSA-CBJ80/ 3. Install the 4-pin tap bracket to which the AC outlet (4- CBJ15/CBJEX pin) is attached, to the specified position of the DMS- B80L/B110S as shown in the illustration with the two screws (PWH4 x 8) respectively For the DMSA-CBJ80 1.
  • Page 89 6-11. Installing the Package Supporting Equipment 4. Install the AC unit (30A) assembly to the specified For the DMSA-CBJ15 position as shown in the illustration on the rear door of the DMS-B80L/B110S with the two screws. 1. Pass the harness of the already wired AC outlet and the AC unit (30A) assembly through the bottom hole of the frame of the DMS-B150L/B210S, and connect them to the AC outlet (4-pin) that is connected to the...
  • Page 90 6-11. Installing the Package Supporting Equipment 3. Install the 4-pin tap fixing plate to which the AC outlet 4. Install the AC unit (30A) assembly to the specified (4-pin) is attached, to the specified position of the position as shown in the illustration on the rear door of DMS-B150L/B210S as shown in the illustration with the DMS-B150L/B210S with the two screws.
  • Page 91 6-11. Installing the Package Supporting Equipment (3) Connect the harness of the already wired AC outlet For the DMSA-CBJEX through the bottom hole of the frame to the AC outlet 1. When one to three units of the DMS-B150L/ of the first extension console. B210S are installed.
  • Page 92 6-11. Installing the Package Supporting Equipment 2. When four to six units of the extension (2) Connect the harness of the already wired AC outlet of consoles are installed. the fourth extension console through the bottom hole (1) Connect the harness (DMS-B150L side) of the already of the frame to the AC outlet of the fifth extension wired AC outlet to the terminal (AC OUT2) of the AC console.
  • Page 93 6-11. Installing the Package Supporting Equipment (4) Install the AC unit (30A) assembly to the position specified by the illustration below on the rear door of the DMS-B150L/B210S with the two screws. Toothed washers 4 4 x 8 AC unit (30A) assembly If drives are installed to both of the upper and lower slots of extension console, limit the number of drives to connect to each of the AC OUT1 and AC OUT2 terminals of the...

  • Page 94: Installation Of The Dmsa-At80

    6-11. Installing the Package Supporting Equipment 6-11-4. Installation of the DMSA-AT80 5. Install the cable clamp 2 with the two screws at the two locations. 1. Remove the screw1 to the screw3 of the seven Cable clamp 2 screws (PWH4 x 8) fixing the top plate of the DMS- B4 x 5 B80L/B110S, and fix the seven hexagonal head cap bolts M4 x 12 (with frange) tentatively that are...
  • Page 95 6-11. Installing the Package Supporting Equipment 7. (This step is for customers who use the DMS-CBJ80 8. While installing the connection cable inside the cable in the Japan. If the unit is used in the area except duct, install the cable duct by hooking it on the screws Japan, perform step 8.) that are tentatively fixed in step 6.

  • Page 96: Installation Of The Dms-Pcu1

    6-11. Installing the Package Supporting Equipment 6-11-5. Installation of the DMS-PCU1 8. Place the DMS-PCU1 on the flat and level surface. 9. Align the keyhole of the right server rail with the pin 1. Slide the server rail on the left side that is supplied on the side of the DMS-PCU1 .
  • Page 97 6-11. Installing the Package Supporting Equipment 12. Align rear end of the server rail with front end of the slide rail carefully. If you want to slide the server rail along with the slide rail, be sure that the DMS-PCU1 is in parallel with the floor.

  • Page 98: Installation Of The Dms-Fsw24/28

    6-11. Installing the Package Supporting Equipment 6-11-6. Installation of the DMS-FSW24/28 3. Install the DMS-FSW24/FSW28 by aligning it with the four screws that are tentatively fixed in step 1 in 1. Tighten the four screws on the PC bracket M (80) and the direction of the arrow.

  • Page 99: Installation Of The Dmsa-Sbe1

    6-11. Installing the Package Supporting Equipment 6-11-7. Installation of the DMSA-SBE1 1. Set the POWER switch of the DMSA-SBE1 to the I (ON) position. DMSA-SBE1 POWER switch 2. Fix the two monitor fixing plates with the four screws (PWH4 x 8). 3.

  • Page 100: Wiring Inside Console

    6-12. Wiring Inside Console 6-12. Wiring Inside Console Connect wirings of each module referring to the illustration below. DMS-FSW24 DMS-B80L/B110S (Using FC cable) Fiberchannel Switcher DMS-B80/B110S PERSONAL COMPUTER/ PETAAPP CONTROLLER Ethernet Hub DMSA-EH16 Terminal To DMS-B80L/B110S Server (CB-105 board) DMSA-TS08 DMS-B80L/B110S (Using SCSI cable) DMS-B80/B110S Host computer...
  • Page 101 6-12. Wiring Inside Console DMS-B150L/B210S/EX150L/EX210S (Using SCSI cable) PERSONAL COMPUTER/ Host computer PETAAPP CONTROLLER (End user) DMS-B150L/B210S Terminal Server DMSA-TS16 To DMS-B150L/B210S (CB-105 board) SCSI Bus Expander DMSA-SBE1 Ethernet Hub DMSA-EH16 DMS-EX150L/EX210S Terminal Server Ethernet Hub DMSA-TS08 DMSA-EH16 SCSI Bus Expander DMSA-SBE1 6-75 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 102 6-12. Wiring Inside Console DMS-B150L/B210S/EX150L/EX210S (Using FC cable) DMS-FSW24 DMS-FSW28 Fiberchannel Switcher Fiberchannel Switcher PERSONAL COMPUTER/ Host computer PETAAPP CONTROLLER (End user) DMS-B150L/B210S Terminal Server DMSA-TS16 To DMS-B150L/B210S (CB-105 board) Ethernet Hub DMSA-EH16 DMS-EX150L/EX210S Terminal Server Ethernet Hub DMSA-TS08 DMSA-EH16 6-76 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...
  • Page 103 6-12. Wiring Inside Console Cable processing at each location Route the each cable referring to the illustration below. Repeat tie Tie mount Cable duct Portion A Portion A Portion B Portion C Repeat tie Tie mount Portion C Portion B (Illustration shows DMS-B80L/B110S.) 6-77 DMS-B150L/B210S/B80L/B110S/EX150L/EX210S...

  • Page 105: Connecting The Cables

    Section 7 Connecting the Cables 7-1. Connecting the Power Cable and 7-1-1. Connecting the Power Cable the UPS Connection diagram UPS (Uninterruptied Power Supply) PetaSite 80/150 The UPS is used to prevent data from damage in the case From Power cord Power Source AC IN AC OUT...

  • Page 106: Signal Input/Output

    7-2. Signal Input/Output 7-2. Signal Input/Output CB-105 board 1 PSC1 : RS232C (D-sub 25-pin, Female) 2 PSC2 : RS232C (D-sub 25-pin, Female) Input and output signals of connectors on the CB-105 board of the basic console are shown below. <External Views> Pin No.
  • Page 107 7-2. Signal Input/Output CB-105 board 1 UPS (Basic) : Parallel (D-sub 9-pin, Female) 2 UPS (Redundant) : Parallel (D-sub 9-pin, Female) <External Views> Pin No. Signal Contents N.C. BYPASS IN Bypass mode : SHORT (Battery non-charge mode) Inverter mode : OPEN (Battery charge mode) AC LEVEL FAIL IN When abnormality is found in commercial...

  • Page 108: Connecting Connectors And Cable

    If any cable is connected to the connectors on the connector panel when installing or servicing, use the connector or cable listed below or equivalent. Connector of DMS-B150L/B210S/B80L/B110S side Matching Connector/Cable Panel Indication Connector Connector Sony Part No. Cable PSC1 D-sub 25-pin, D-sub 25-pin, 1-566-356-11 Female...

  • Page 109: Operation Check

    Section 8 Operation Check When all of the installation works are complete, perform the system initialization operation test using the test menu of the MMT display. A test program is available on PSC to perform operation test. Either one or two L-cassettes on which barcode label is attached are required for the test program. 1.
  • Page 111 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
  • Page 112 DMS-EX210S DMS-EX150L DMS-B110S DMS-B80L DMS-B210S Printed in Japan Sony Corporation DMS-B150L (SY) E 2002. 5 16 9-967-907-04 B&P Company ©2000...

This manual is also suitable for:

Petasite dms-b210sPetasite dms-b80lPetasite dms-b110sPetasite dms-ex150lPetasite dms-ex210s

Table of Contents