SHOWTEC Compact Power Lightset V2 User Manual page 23

Iroubleshooling
No
tighl,
No
Movemenl -
All Producls
This
troubleshooting guide
is
meont lo help solve simple problems.
lf
o
problem
occurs, corry
out the steps
below
in
sequence
until o
soluTion
is
found. Once the
uniT
operoles
properly, do
not corry
out following
steps.
lf The
light
effect
does
not operote properly, reler servicing
To
o technicion.
Response: Suspect
two
poienliol
problem
oreos:
fhe power
supply,
the
fuse.
l.
Power supply.
Check
thoT
ihe
unit
is
plugged inlo on oppropriote power
supply.
2.
The
fuse.
Reploce the
fuse. See
poge
20
for
replociÀg the
fuse.
No Response
lo
DMX
R':-'sponse:
Suspect
the
DMX
coble
or
connectors. o controller
molfuncTion,
o
light
effect
DMX
cord
mnlfunction.
l.
Check the
DMX
coble:
Unplug
the
unit;
chonge ihe
DMX
coble; then reconnect to
elecTricol
power.
Try
your
DMX
control ogoin.
2. Determine
whelher the controller
or
lighT
effect
is oT
foult.
Does
The
controller
operole
properly with
olher
DMX
producls
?
lf not,
toke ihe
conTrolier in for
repoir.
lf so.
toke the
DMX
coble
ond the
light
effect lo
o
quolified technicion.
Problem Proboble
cousels]
Remedv
One or more
fixlures
ore
complelely
deod.
No
power
lo lhe fixlure
.Check
Thot
power
is
swilched on
ond
cobles ore
plugged
in.
Primory fuse
blown.
'Reploce
luse.
Fixlures
reset
conectly,
bul
oll
respond eroticolly
or nol ot
oll
lo
the
.Connect
côntrôller
3-pin
XLR
Oul of lhe controller does
nôl
motch
XLR
Out of the
firsl
fixture on
the
link
(i.e.
signol
is
reversed).
'lnstoll
o
phose
reversing
coble
between
the
conTroller
ond the
firsl
fixlure on the
link.
Fixlures reset
correclly,
bul some
Poor
doto quolity
'Check
dolo
quolity.
lf much lower
thon
100
percent,
the problem moy
be o bod
dolo
link
connec'fion, poor
quolily
or
broken cobles,
missing
terminotion plug,
or
o
defective
fixture disturbinq the
link.
Bod
doto
link connec'tion
'
lnspect connections ond
cobles.
Correci poor conneclions.
Repoir or
reoloce domooed cobles-
Doto
link
nol
terminoled wiih
120
Ohm
têrminôtiôn
ôh
rô
lnsert
lerminotion plug
in
output
jock
of the
lôsl
fixfi rre
ôn
lhê
link
lncorect
oddressino of lhe
fixlures.
Check oddress
settinq.
respond eno{icolly
or
not ol oll to the
conlroller.
One of the
fixlures
is
defeclive ond
dislurbs
dolo
tronsmission
on the
link.
'Byposs
one
fixture
ot
o
lime
until
normol
operotion
is
regoined: unplug
both conneclors
ond connect
them
direclly logether.
' Hove the defeclive
fixture
serviced
bv ô ouolified technicion.
3-pin
XLR
Oul on the
fixtures
does
nol
motch
{pins 2
ond
3
reversed}.
'lnstoll o phoseieversing coble
between
the
fixtures or
swop pin
2
ond
3
in
ihe fixture, thot behoves
No
light
The
power supply sellings
do
n01
motch
locol AC
voltoge ond
frequency.
Disconnecl
fixture.
Check
setf ings
ond conect
if necessory.
LEDs
domoged
' Disconnect fixture
ond
re'turn
lo your
Lomp culs out Fixture
is
too hot.
'Allow
fixlure to cool.
'Turn uo the
oir
conclitionino
The
power supply
sel'lings
do nol
motch locol
AC
voltqgê ond
' Disconnecl fixlure. Check setlings
ond conect
if necessory.
21