Venting Requirements And Options - Direct Vent Only - Vermont Castings Stardance SDV30 Installation And Operating Manual

Stardance Direct Vent/Natural Vent Gas Heater
Venting Requirements and Options -
Direct Vent ONLY
Approved Vent System Components
The Stardance Heater must be vented to the outdoors
through an adjacent exterior wall or through the roof.
The venting system must be comprised of the appropri-
ate listed venting components specified on this page.
These parts are available from DuraVent Corporation or
your Vermont Castings Dealer.
See Figure 4 for dimensions relevant to the standard
minimum-vent kits.
Simpson DuraVent Components
Minimum Horizontal Vent Kit 2792
Starter Pipe Assembly
(incl. inner & outer sections)
90° Elbow, Blk.
45° Elbow, Gal.
6" Straight, Blk.
9" Straight, Blk.
11" - 14B\," Adjustable Straight Section
12" Straight
24" Straight
36" Straight
48" Straight
Horizontal Vent Cap
Wall Plate
Vinyl Siding Shield
Snorkel Termination - 14"
Snorkel Termination - 36"
Wall Strap
Cathedral Ceiling Support Box
Storm Collar
Firestop Spacer
Flashing 0/12 - 6/12
Flashing 6/12 - 12/12
Steel Chimney
Kit A
Kit B
Kit C
Masonry Chimney Kit
Vertical Termination Cap (High Wind)
Vertical Termination Cap (Low Profile)
*Included in Minimum Horizontal Vent Kit #2792
All DuraVent Straight vent pipe sections have a net
length 1¹⁄₂" (37mm) less than the nominal dimension;
i.e., a 6" (152mm) Straight pipe section has an effective
length of 4¹⁄₂" (115mm).
CFM Vent Components
The following kits are available to meet the needs of
most installations. All pipe has a 7" outer diameter and
includes a 4" diameter inner section. A (CG) designa-
tion indicates the part is finished in Charcoal Gray paint.
Consult your dealer about other vent parts that may be
appropriate to complete the installation.
12
Min. Through the Wall Vent Kit
(1) 90-Degree Elbow (CG)
(1) 24" Straight pipe (CG)
(1) 24" - 42" Adjustable Straight Pipe
(1) Side Wall Termination
(1) Firestop
(1) Zero-clearance sleeve
(1) Hardware package
(1) Finishing plate (CG)
(1) Finishing collar (CG)
(4) Charcoal Gray flue pipe rings
Starter Kit for Below Grade Installation
(1) Snorkel Termination (7TDVSNORK)
Vertical Termination Kit, 1/12-6/12 Pitch
(1) Combination Horizontal Offset / Roof Support
(1) Vertical Termination
(1) Storm Collar
(1) 1/12-6/12 Flashing
2768*
(1) Finishing Plate (CG)
990B*
(1) Finishing Collar (CG)
945
(1) Polished Brass Flue Pipe Ring
908B*
(1) Hardware Package
907B
Vertical Termination Kit, 7/12-12/12 Pitch
911B
(1) 7/12 - 12/12 Flashing
906
and all of the other Vertical Termination parts.
904B*
Vertical Termination, Flat Roof
903B
(1) Flat Flashing
and all of the other Vertical Termination parts.
902
Twist Lock 12" Straight Pipe (CG)
984*
(1) 12" Non-adjustable Pipe
940*
Twist Lock 12"-18" Straight Pipe (CG)
950
(1) 12" - 18" Adjustable Pipe
982
Twist Lock 24" Straight Pipe (CG)
981
(1) 24" Non-adjustable Pipe
988
Twist Lock 48" Straight Pipe (CG)
941
(1) 48" Nonadjustable Pipe
953
Twist Lock 45-Degree Elbow (CG)
for vertical offsets
963
(1) 45-degree Elbow
943
Draft Hood Adapter
943S
NV Stove Kit
(1) 7" Diameter Polished Brass Trim Ring
931
(1) 48" Nonadjustable Pipe (CG)
932
(1) 24" Nonadjustable Pipe (CG)
933
(1) Finishing Plate
934
(1) Finishing Collar (CG)
991
(1) 90 Degree Elbow (CG)
Stove Kit
980
Includes all parts in the 7FSSK plus the Draft Hood Adapter
FSDHAG
Combination Offset/Roof Support
Attic Insulation Shield
7" Charcoal Gray Pipe Rings, (4)
7" Polished Brass Pipe Rings (4)
Wall Thimble
NOTE: Direct vent pipe may be used on the Natural
Vent system from the top of the draft hood adapter to
the ceiling.
7TFSSK
7TDVSKS
7TDVSKVA
7TDVSKVB
7DVSKVF
7TFSDVP12
7TFSDVP1218
7TFSDVP24
7TFSDVP48
7TFSDVT45
FSDHAG
7FSSK
7FSDHASK
7DVCS
7DVAIS
7FSDRG
7FSDRP
942G
20007065