However, like all electronic equipments, the AV-GM07L3-S1 should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
RS-232 and IP control ● Easy installation with rack-mounting ● Fast response time – 2~4 seconds for channel switch PACKAGE CONTENTS ● 1x AV-GM07L3-S1 ● 1x UL AC C13 power cord ● 17x IR receiver ● 16x IR blaster* ●...
SPECIFICATIONS Model Name AV-GM07L3-S1 Technical AV-GM07L3-S1 True 16x16 matrix switcher Role of usage Transmitter [TX] HDMI compliance HDMI Deep Color & full 3D & 4K2K@30 Yes [HDCP 1.4] HDCP compliance Video bandwidth Single-link 340MHz [10.2Gbps] Video support 480i / 480p / 720p / 1080i / 1080p@60/ 4K2K@30 Audio support Surround sound (up to 7.1ch) or stereo digital audio...
PANEL DESCRIPTIONS Transmitting unit ► AV-GM07L3-S1 Front Panel Power Switch: Power ON/OFF switch 7-segment LED: for output 1-16 status Source Status: Input source indicator LED IR SENSOR: IR sensor for receiving the IR commands from IR remote Push Button: Select the output and input...
System IR Receiver: Ext. IR receiver AC Power: 100-240V Receiving unit ► CV-57VA-RX [Sold Separately] LED: Power LED, Status LED, Link LED, HDCP LED Power LED: This LED light always shine is meant that works fine. Status LED: This LED light is blinking it means functions well. ...
IR BLASTER: IR control on individual display device IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote controls of AV-GM07L3-S1 and all other HDMI source devices. CAUTION! Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders.
You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft) may not work. CONNECTION DIAGRAM...
OPERATION APPROACH Method A: Push-in Button Input / Output Mapping 1) Use the “LEFT” or “RIGHT” push button to select the output desired to switch sources to. 2) Use the “UP” or “DOWN” push button to select the specific source 3) Press “SET”...
Page 11
Example of function key Operation Procedure 7-Segment LED IN / OUT Switch Switch + number(input) + To + number(output) + Take 1. Press “SWITCH” button 2. Press number key “3” to select Input Ex: Input 3 To Output 4 3. Press “To” button 4.
Page 12
4. Press “ALL” to select All Input 5. Press “TAKE” button 0 (success) F (fail)
Page 13
Learn Output EDID Learn + number(output) + To + number(input) + Take 1. Press “LEARN” button 2. Press number key “2” to select Output Ex: Learn Output 2 Input 3. Press “To” button 4. Press number key “3” to select Input 5.
Page 14
Method C: Software Control through RS-232 port / Ethernet port System Requirement 1) OS Information: MS WinXP/7 2) Baud rates: 9600 3) Software size: 3 MB 4) Minimum RAM requirement: 256 MB I/O Routing Button Rename I/O Button EDID Button Network Button F/W Update &...
Page 15
1. I/O Routing Button I/O: Select the input Save Mapping: Select Mapping(1-8) Click “Save” button to save current mapping Preset Mapping: Select Mapping(1-8) Click “Recall” button to recall previous mapping which are saved...
Page 16
Rename I/O Button Rename I/O: Rename output name Rename input name Rename Mapping: Rename Mapping name...
Page 18
Click “Learn” button to learn default EDID Learn EDID From Display Select output Select Input Click “Learn” button to learn display EDID Load EDID File to Input Select Input Click “Load” button to select the EDID file View EDID ...
Page 19
Select the EDID content Click “Save EDID on Computer” to save the generated EDID as a file Network Button...
Page 20
Save Setting Save the IP address which you key in on the column Read Setting: Read the IP address from the device PS: The default IP address is 192.168.1.111...
Page 21
System Button Version: Get the firmware version information Factory Reset To do factory default reset Help To view the steps of the firmware update Firmware Update Main Board Firmware Update Valens Firmware Update DB Board ...
Page 22
COM Port Selection Click “ ” button to select COM Port Connection Status Connected Status: Connecting Status: Disconnected Status: Connect/Disconnect Button Click this button “ ” to change connection status RS-232 Button Click “ ” button to switch to RS-232 function. ...
Page 23
Method D: Web Interface Control The default IP address: 192.168.1.111 Account: admin Password: matrix I/O Routing Button Setting Button EDID Button Refresh I/O Status & Read I/O Name Button 1. I/O Routing Button...
Page 24
I/O: Select the input Save Mapping: Select Mapping (1-8) Click “Save” button to save current mapping Recall Mapping: Select Mapping (1-8) Click “Recall” button to recall previous mapping which are saved Setting Button...
Page 25
Rename I/O: Rename output name Rename input name Rename Mapping: Rename Mapping name Password change: (the password has to be 6 characters) Key in “old password” Key in “new password” Key in “new password” again...
EDID LEARNING The EDID learning function is only necessary whenever you encounter any display on the HDMI output port that cannot play audio and video properly. Because the HDMI source devices and displays may have various level of capability in playing audio and video, the general principle is that the source device will output the lowest standards in audio format and video resolutions to be commonly acceptable among all HDMI displays.
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. Also, the technical information contained herein regarding the AV-GM07L3-S1 features and specifications is subject to change without further notice.
Need help?
Do you have a question about the AV-GM07L3-S1 and is the answer not in the manual?
Questions and answers